
ROBOLAB Starter Building Set
미니피규어 (1)
부품 목록 (216)

Technic Gear 40 Tooth
×4
Slope Inverted 45° 2 x 1
×4
Slope Inverted 45° 2 x 1
×4
Technic Brick 1 x 2 [1 Pin Hole]
×4
Plate 1 x 4
×4
Slope Inverted 33° 3 x 2, No Connections between Studs, Ovoid Bottom Pin
×4
Bracket 2 x 2 - 2 x 2
×4
Arm Grab Jaw
×4
Light Brick 1 x 2 with Single Side Light
×4
Arm Piece with Pin, 2 Fingers
×4
Brick Curved 2 x 3
×4
Technic Cam
×4
Technic Beam 1 x 9 Bent (6 - 4) Thick
×4
Technic Beam 1 x 3 Thin
×4
Hose, Ribbed 7mm D. 9L / 7.2cm
×4
Hose, Ribbed 7mm D. 9L / 7.2cm
×4
Hose, Ribbed 7mm D. 12L / 9.6cm
×4
Technic Rubber Belt Medium [26mm ID] [Round Cross Section]
×4
Sensor, Touch
×4
Brick 1 x 2 x 5 with Blocked Open Studs and Bottom Stud Holder with Asymmetric Ridges
×3
Technic Brick 1 x 10 [9 Pin Holes]
×3
Sensor, Light with Fixed Cable
×3
Slope 45° 2 x 2
×3
Technic Brick 1 x 2 [2 Pin Holes]
×3
Technic Brick 1 x 8 [7 Pin Holes]
×3
Technic Brick 1 x 6 [5 Pin Holes]
×3
Motor, 9V Mini [Lightweight New Style]
×3
Plate Round 1 x 1 with Solid Stud
×3
Plate Round 1 x 1 with Solid Stud
×3
Technic Rubber Belt Medium [24mm ID] [Round Cross Section]
×3
Wheel 49.6 x 28 VR with X Axle Hole
×2
Brick 2 x 2 Corner
×2
Wedge Plate 3 x 6 Cut Corners
×2
Brick Special 1 x 2 with Pin
×2
Brick 1 x 16
×2
Tile Special 1 x 1 with Clip and Straight Tips
×2
Antenna 8H Whip
×2
Plate Special 2 x 2 with 2 Pin Holes
×2
Brick 2 x 4
×2
Brick 1 x 4
×2
Plate 2 x 4
×2
Dome Hemisphere 4 x 4 Multifaceted
×2
Plate Special 1 x 2 with 4 x 4 disk at 90 degrees
×2
Plate 2 x 3
×2
Plate 2 x 2
×2
Plate 1 x 2
×2
Tile 2 x 2 with Groove
×2
Technic Beam 1 x 11.5 Double Bent Thick
×2
Technic Brick 1 x 2 with Axle Hole Type 1 [+ Opening] and Bottom Pin
×2
Technic Beam 1 x 7 Thin
×2
Technic Axle and Pin Connector Perpendicular 3L with Pin Hole
×2
Tyre Offset Tread 24 x 8
×2
Plate 1 x 3
×2
Tyre 43 x 17
×2
Slope Inverted 45° 2 x 1
×2
Plate 1 x 6
×2
Turntable 2 x 2 Plate - Top
×2
Turntable 2 x 2 Plate, Base
×2
Technic Brick 1 x 4 [3 Pin Holes]
×2
Technic Brick 1 x 16 [15 Pin Holes]
×2
Technic Steering Pulley Large
×2
Plate 2 x 6
×2
Plate 2 x 10
×2
Technic Brick 1 x 12 [11 Pin Holes]
×2
Hinge Brick 1 x 2 Base
×2
Hinge Brick 1 x 2 Top Plate Thin
×2
Brick Round 2 x 2 with Axle Hole
×2
Dish 4 x 4 Inverted [Radar]
×2
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×2
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×2
Plate Special 1 x 1 with Clip Vertical [Thick U Clip]
×2
Arm Grab Jaw Holder, 3 Fingers
×2
Hinge Plate 1 x 2 with 3 Fingers [Hollow Studs]
×2
Hinge Tile 1 x 2 1/2 with 2 Fingers on Top
×2
Cone 1 x 1 [No Top Groove]
×2
Cone 1 x 1 [No Top Groove]
×2
Wire with Brick 2 x 2 x 2/3 Pair, 162L
×2
Plate Special 1 x 1 with Clip Horizontal [Thick U Clip]
×2
Creature Body Part, Dragon Wing
×2
Tyre 30.4 x 14 VR
×2
Tyre 49.6 x 28 VR
×2Storage Bin Lid, Dacta, 19 x 24
×2
Tread Large, Technic [34 Links]
×2
Hose Rigid 3mm D. 19L / 15.2cm
×2
Hose Rigid 3mm D. 36L / 28.8cm
×2
Rubber Belt Small [15mm ID] [Round Cross Section]
×2
Technic Rubber Belt Medium [24mm ID] [Round Cross Section]
×2Storage Bin, Dacta, Medium
×2
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×1
Motor Cover, 9V Micromotor 2 x 2
×1
Motor Cover, 9V Micromotor 2 x 2 Base
×1
Motor, 9V Micromotor 2 x 2
×1
Brick 2 x 4
×1
Brick 2 x 3
×1
Brick 1 x 6
×1
Plate 2 x 3
×1
Plate 2 x 2
×1
Plate 2 x 2
×1
Wing Insectoid Large with Arm Hinge and Circuitry Print Left (Print on Top, Tip on Left, Logo at Back Edge)
×1
Wing Insectoid Large with Arm Hinge and Circuitry Print Right (Print on Top, Tip on Right, Logo at Back Edge)
×1