
The Zombies
미니피규어 (4)
부품 목록 (167)

Tyre 30 x 10.5 Offset Tread [Centre Band]
×2
Wheel 18 x 8 with Fake Bolts and Shallow Spokes
×2
Plate Special 1 x 4 with Angled Tubes
×2
Plate Round 1 x 1 with Solid Stud
×2
Technic Pin Connector Round [Slotted]
×2
Equipment Telescope / Torch / Spyglass, Support Round 1 x 1 x 1 2/3
×2
Flame / Headwear Accessory Plume / Feather, Triple Point
×2
Technic Gear 12 Tooth Bevel
×2
Technic Pin Connector Double with Bar [2 Holes]
×2
Weapon Gun / Torch (Space) [No Grooves]
×2
Technic Axle 4 with Stop
×2
Plate Special 1 x 2 with Bar Up [Horizontal Arm 5mm]
×2
Bracket 1 x 2 - 1 x 2
×2
Rock 1 x 2 Crystal Stepped with Black Zombie Print
×1
Plate Special 2 x 2 with Pin on Bottom
×1
Brick Special 1 x 4 with Groove
×1
Brick 2 x 4
×1
Brick 1 x 6
×1
Animal, Bat
×1
Vehicle Base 6 x 5 x 2 [2 Seats]
×1
Insect, Spider
×1
Plate 4 x 4
×1
Plate 4 x 8
×1
Tile 1 x 1 with White and Red Gauge Print
×1
Technic Beam 1 x 5 Thick
×1
Technic Gear 8 Tooth
×1
Plate 1 x 6
×1
Steering Stand 1 x 2 with Black Steering Wheel
×1
Plate Special 1 x 2 with Handles [Flat Ends / Low Attachment]
×1
Brick Round 2 x 2 with Axle Hole
×1
Plate 6 x 6
×1
Bar 1 x 4 x 2 with Studs
×1
Plate 8 x 8
×1
Panel 1 x 4 x 1 with Rounded Corners [Thick Wall]
×1
Equipment Pot / Cauldron 3 x 3 x 1 & 3/4 with Handles
×1
Plate Special 1 x 4 Offset with Bar Holes
×1
Plate Special 1 x 2 [Side Handle Closed Ends]
×1
Slope Curved 4 x 6 x 2/3 Triple Curved with 4 Studs
×1
Slope Inverted 45° 6 x 1 Double with 1 x 4 Recessed
×1
Plant / Creature Body Part, Vine / Tail / Tentacle / Bionicle Spine, Spiky
×1
Plant / Creature Body Part, Vine / Tail / Tentacle / Bionicle Spine, Spiky
×1
Plate Round 4 x 4 with Pin Hole
×1
Plate Round 1 x 1 with Solid Stud
×1
Gearbox 4 x 4 x 1 2/3 with 1 x 2 Cutouts, Pin Holes
×1
Tool Hammer / Sledgehammer
×1
Plate Special 2 x 2 with Groove and Center Stud (Jumper)
×1
Train Cow Catcher, Plate Special 2 x 6 with Sloped Bars
×1
Tile Round 1 x 1
×1
Bracket 1 x 2 - 2 x 2 Inverted
×1
Technic Bush
×2
Technic Pin 1/2
×2
Bar 1L with Clip [Cut Edges and One Side Hole] [Gap in Clip]
×2
Plate Round 1 x 1 with Solid Stud
×2
Tile Round 1 x 1
×2
Technic Pin with Friction Ridges Lengthwise and Center Slots
×1
Tile 1 x 1 with White and Red Gauge Print
×1
Technic Pin without Friction Ridges Lengthwise
×1
Bar 1L with Clip [Cut Edges and One Side Hole] [Gap in Clip]
×1
Animal Body Part, Barb / Claw / Tooth / Talon / Horn, Small
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Plate Round 1 x 1 with Solid Stud
×1
Plate Round 1 x 1 with Solid Stud
×1
Plate Round 1 x 1 with Solid Stud
×1
Flame / Headwear Accessory Plume / Feather, Triple Point
×1
Technic Gear 12 Tooth Bevel
×1
Tile Round 1 x 1
×1


