
Fangpyre Mech
미니피규어 (2)
부품 목록 (82)

Plate Special 1 x 2 with Handle on End [Closed Ends]
×16
Bracket 1 x 2 - 2 x 2
×14
Slope 18° 2 x 1 x 2/3 with 4 Slots / Grate
×10
Plate 2 x 4
×9
Tile Round 1 x 1
×9
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×6
Bracket 1 x 2 - 2 x 2
×6
Slope 18° 2 x 1 x 2/3 with 4 Slots / Grate
×6
Slope Curved 4 x 1 No Studs [Stud Holder with Asymmetric Ridges]
×6
Hinge Plate 1 x 4 Swivel Top / Base - Solid Clip [Complete Assembly]
×6
Slope Curved 4 x 1 Double with No Studs
×6
Plate 2 x 6
×5
Technic Brick Modified 2 x 2 with Solid Ball and Axle Hole
×5
Plate Special 1 x 2 with Clips Horizontal [Open O Clips]
×5
Plate Round 1 x 1 with Solid Stud
×5
Slope 30° 1 x 2 x 2/3
×5
Technic Brick Special 2 x 2 with Ball Socket Wide and Axle Hole
×5
Brick 1 x 8
×4
Plate 1 x 2
×4
Slope Curved 2 x 2 with Lip, No Studs
×4
Brick Round 1 x 1 Open Stud
×4
Wheel Arch, Mudguard 1 x 4 1/2
×4
Brick Curved 1 x 2 x 1 1/3 with Curved Top
×4
Slope 18° 2 x 1 x 2/3 with 4 Slots / Grate
×4
Wheel Arch, Mudguard, 1 1/2 x 6 x 1 [Arch Extended]
×4
Panel 1 x 2 x 2 [Side Supports / Hollow Studs]
×4
Slope 45° 2 x 1 with 2/3 Cutout [Original Version]
×4
Slope Inverted 33° 3 x 2, Connections between Studs, Ovoid Bottom Pin
×3
Tile Round 2 x 2 with Bottom Cross
×3
Plate Special 1 x 2 Side Handle [Free Ends]
×2
Lever Small Base with Black Lever
×2
Brick 2 x 2
×2
Plate 2 x 2
×2
Tile 1 x 2 with Groove
×2
Technic Ball Joint
×2
Slope Inverted 45° 2 x 2 Double Convex
×2
Technic Brick 1 x 2 [1 Pin Hole]
×2
Plate Special 1 x 1 with Clip Light, Bar Hole [Thick Ring]
×2
Wedge Curved 6 x 2 Right, Inner Ridges
×2
Wedge Curved 6 x 2 Left, Inner Ridges
×2
Hinge Plate 1 x 2 Locking with 1 Finger on Side, with Groove
×2
Technic Rotation Joint Ball Loop with Two Perpendicular Pins with Friction
×2
Technic Brick Special 2 x 2 with Pin Hole, Rotation Joint Ball Half [Vertical Side]
×2
Bar 1L with Clip [Cut Edges and One Side Hole] [Gap in Clip]
×2
Plate Special 1 x 1 with Tooth
×2
Slope Inverted 45° 6 x 1 Double with 1 x 4 Recessed
×2
Arm Mechanical with Clip [Thin Support]
×2
Hinge Plate 1 x 2 Locking with 2 Fingers on Side, 9 Teeth
×2
Plate Round 4 x 4 with Pin Hole
×2
Brick Curved 1 x 2 x 1 1/3 with Curved Top
×2
Bar 5L with Handle (Friction Ram)
×2
Animal Body Part, Barb / Claw / Tooth / Talon / Horn, Medium
×2
Large Figure Skeletal, Limb, 4L with Ball Joint on Axle and Ball Socket
×2
Plate Special 1 x 2 [Top Clip]
×2
Brick Round 2 x 2 [Grill]
×2
Bracket 1 x 2 - 2 x 4
×2
Slope Curved 4 x 2 No Studs
×2
Plate Special 2 x 2 with 1 Pin Hole [Split Underside Ribs]
×1
Brick 2 x 4
×1
Plate 4 x 8
×1
Bar 4L (Lightsaber Blade / Wand)
×1
Bar 4L (Lightsaber Blade / Wand)
×1
Plant, Banana
×1
Plate 1 x 4
×1
Animal Body Part / Plant, Tail / Neck / Branch / Trunk, Middle Section with Pin, Round Pin Hole
×1
Animal Body Part / Plant, Tail / Claw / Horn / Branch / Tentacle, End Section
×1
Wedge Curved 4 x 4 No Top Studs
×1
Technic Brick Special 2 x 2 with Pin Hole, with 2 Rotation Joint Sockets
×1
Cone 1 x 1 [Top Groove]
×1
Plate Special 1 x 1 with Clip Horizontal [Thick U Clip]
×1
Technic Pin 1/2 with 2L Bar Extension
×1
Plate Special 1 x 2 with Angular Extension and Flexible Lime Tip
×1
Turntable 4 x 4 Square Base, Locking
×1
Bar 6L with Stop Ring
×1Sticker Sheet for Set 9455-1
×1
Brick Round 4 x 4 Centre Hole
×1
Slope Brick Curved 2 x 4 x 2/3 No Studs, with Bottom Tubes
×1
Wing / Blade 1 x 4 with Pin Hole
×1
Lever Small Base with Black Lever
×1
Bar 1L with Clip [Cut Edges and One Side Hole] [Gap in Clip]
×1
Plate Round 1 x 1 with Solid Stud
×1
Tile Round 1 x 1
×1
