
Boulder Blaster
미니피규어 (2)
부품 목록 (87)

Technic Pin with Friction Ridges Lengthwise and Center Slots
×12
Slope 18° 2 x 1 x 2/3 with 4 Slots / Grate
×12
Tile 1 x 2 with Groove
×11
Technic Bush
×10
Tile 1 x 2 with Groove
×9
Technic Brick 1 x 4 [3 Pin Holes]
×9
Technic Brick 1 x 1 with Pin Hole
×9
Plate 1 x 2
×8
Plate 1 x 4
×8
Brick Round 2 x 2 with Axle Hole
×8
Technic Axle Pin with Friction Ridges Lengthwise
×8
Technic Wedge Belt Wheel [aka Pulley]
×7
Wheel 30.4 x 20 without Pinholes, with Reinforced Rim
×7
Tile Special 1 x 1 with Clip and Straight Tips
×6
Brick Round 2 x 2 Dome Top, Blocked Open Stud, Bottom Axle Holder
×6
Plate 1 x 6
×6
Technic Axle 5.5 with Stop [Rounded Short End]
×6
Tile Special 1 x 2 Grille with Bottom Groove
×5
Plate 2 x 8
×5
Plate Special 1 x 2 Side Handle [Free Ends]
×4
Plate 1 x 2
×4
Brick Round 1 x 1 Open Stud
×4
Plate 1 x 3
×4
Plate Special 1 x 2 with 1 Stud with Groove (Jumper)
×4
Brick Special 1 x 1 with Headlight
×4
Plate Round 1 x 1 with Solid Stud
×4
Plate Round 1 x 1 with Solid Stud
×4
Plate 2 x 4
×3
Brick Special 1 x 4 with 4 Studs on One Side
×3
Tile 1 x 1 with Groove
×3
Technic Brick 1 x 2 with Axle Hole Type 2 [X Opening]
×3
Tile Round 2 x 2 with Bottom Cross
×3
Equipment Dynamite Sticks
×3
Technic Axle 3 with Stud
×3
Hinge Panel 6 x 3
×2
Brick Special 1 x 2 with Grille
×2
Brick 2 x 4
×2
Brick 2 x 3
×2
Brick 1 x 6
×2
Plate 1 x 1
×2
Rock 1 x 1 Crystal 5 Point
×2
Technic Brick 1 x 2 [2 Pin Holes]
×2
Technic Brick 1 x 14 [13 Pin Holes]
×2
Technic Beam 1 x 9 Bent (7 - 3) Thick
×2
Technic Pin Long without Friction Ridges
×2
Brick 1 x 3
×2
Slope Inverted 45° 2 x 1
×2
Slope 75° 2 x 2 x 3 [Hollow Studs]
×2
Technic Brick 1 x 2 [1 Pin Hole]
×2
Technic Axle 8
×2
Plate 1 x 4
×2
Brick Round 2 x 2 with Axle Hole
×2
Brick Special 1 x 1 with Headlight
×2
Plate Special 2 x 2 with Grills
×2
Brick Curved 6 x 1 Inverted
×2
Hinge Plate 1 x 2 Locking with 1 Finger On End, with Groove
×2
Hinge Plate 1 x 2 Locking with 2 Fingers On End, with Groove, 9 Teeth
×2
Technic Tread Large [36 Links]
×2
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×2
Cone 1 x 1 [Top Groove]
×2
Plate Special 1 x 2 with Handle on End [Closed Ends]
×2
Hinge Brick 2 x 2 Top Plate Thin
×2
Technic Pin Long with Friction Ridges Lengthwise, 2 Center Slots
×2
Technic Pin with Friction Ridges Lengthwise and Towball
×2
Brick 2 x 3
×1
Brick 2 x 2
×1
Box / Crate with Handholds 3 x 4 x 1 2/3
×1
Equipment Stretcher Holder
×1
Plate 2 x 3
×1
Plate 4 x 4
×1
Bar 4L (Lightsaber Blade / Wand)
×1
Technic Brick 1 x 2 [2 Pin Holes]
×1
Technic Beam 2 x 4 L-Shape Thick
×1
Technic Beam 1 x 11 Thick
×1
Steering Stand 1 x 2 with Black Steering Wheel
×1
Equipment Shovel [Rounded Handle End]
×1
Tool Pickaxe
×1
Plate Special 8 x 8 with Grille [Hole in Center]
×1
Bracket 1 x 2 - 2 x 2
×1
Slope Curved 4 x 6 x 2/3 Triple Curved with 4 Studs
×1
Technic Axle Connector Hub with 3 Axles at 120°
×1
Plate Special 1 x 2 with Clips Horizontal [Thick U-Clips]
×1
Slope Brick Curved 2 x 4 x 2/3 No Studs [No Bottom Tubes]
×1
Plate Special 1 x 4 with Angled Tubes
×1
Roll Cage 6 x 4 x 3 1/3
×1
Rubber Belt Small [15mm ID] [Round Cross Section]
×1Sticker Sheet for Set 8707-1
×1
