
Mission 8: Volcano Base
미니피규어 (6)

Dr. Inferno
fig-002260×1

Fire Arm
fig-002262×1

Claw-Dette
fig-002263×1

Agent Trace
fig-002264×1

Agent Fuse
fig-002265×1

Agent Chase with Helmet
fig-002266×1
부품 목록 (218)

Slope 45° 2 x 1 with Bottom Pin
×45
Slope 75° 2 x 1 x 3 with Hollow Stud
×43
Brick 1 x 2
×23
Slope 45° 2 x 1 with Bottom Pin
×23
Brick 1 x 1
×19
Brick 2 x 2
×16
Dish 2 x 2 Inverted [Radar]
×16
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×13
Tile Special 1 x 2 Grille with Bottom Groove
×11
Plate 1 x 2
×11
Plate 2 x 2 Corner
×10
Plate 1 x 1
×10
Brick 2 x 2 Corner
×8
Brick Special 1 x 1 with Handle
×8
Brick 1 x 1
×8
Plate 1 x 2
×8
Support 2 x 2 x 10 Girder Triangular Vertical - Type 3 - Axle Hole, 3 Posts
×8
Technic Axle 3 with Stud
×7
Lever Small Base with Black Lever
×6
Bar 4L (Lightsaber Blade / Wand)
×6
Tile 1 x 1 with Groove
×6
Technic Axle and Pin Connector Toggle Joint Smooth
×6
Wedge Plate 4 x 2 Left
×6
Technic Axle Pin with Friction Ridges Lengthwise
×6
Technic Axle 3
×6
Technic Pin 1/2 with 2L Bar Extension
×6
Brick Special 2 x 2 with Pin and Axle Hole
×6
Plate 1 x 4
×5
Brick Arch 1 x 5 x 4 [Continuous Bow]
×4
Brick 1 x 2 x 5 with Blocked Open Studs and Bottom Stud Holder with Asymmetric Ridges
×4
Tile Special 1 x 1 with Clip and Straight Tips
×4
Plant, Round 1 x 1 - 3 Bamboo Leaves
×4
Plate 2 x 3
×4
Plate 2 x 2
×4
Hinge Brick 1 x 2 Locking with 2 Fingers Horizontal End, 9 Teeth
×4
Hinge Brick 1 x 2 Locking with 1 Finger Horizontal End
×4
Brick Round 1 x 1 Open Stud
×4
Brick Arch 1 x 8 x 2
×4
Slope Inverted 45° 2 x 1
×4
Plate 1 x 6
×4
Slope 65° 2 x 2 x 2 with Bottom Tube
×4
Turntable 2 x 2 Plate - Top
×4
Turntable 2 x 2 Plate, Base
×4
Technic Brick 1 x 2 [1 Pin Hole]
×4
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×4
Brick Special 1 x 1 with Headlight
×4
Seat / Chair 2 x 2 with Center Sprue Mark
×4
Plate Special 1 x 1 with Clip Light, Bar Hole [Thick Ring]
×4
Technic Pin 1/2
×4
Rock Panel 2 x 4 x 6 with Marbled Dark Bluish Gray Pattern
×4
Cone 1 x 1 [Top Groove]
×4
Brick Curved 1 x 2 x 1 1/3 with Curved Top
×4
Wedge Plate 6 x 6 Cut Corner
×4
Wave / Flame Rounded with Base Pegs
×4
Tile Special 1 x 2 Grille with Bottom Groove
×3
Brick 1 x 16
×3
Plate 2 x 4
×3
Slope 45° 2 x 2
×3
Slope 45° 2 x 2 with Green Radar, Green/Red Buttons and Disk Slot Print
×3
Technic Axle and Pin Connector Angled #1
×3
Technic Axle 2 Notched
×3
Technic Bush 1/2 Smooth with Axle Hole Semi-Reduced
×3
Technic Bush
×3
Plate 2 x 6
×3
Technic Wedge Belt Wheel [aka Pulley]
×3
Light Cover 1 x 1 Round with Internal Bar / Bionicle Barraki Eye
×3
Rock Panel Triangular 3 x 8 x 7 (aka LURP)
×3
Technic Axle 1.5 with Perpendicular Axle Connector (Technic Pole Reverser Handle)
×3
Wing, Tail 4 x 1 x 3
×2
Wedge Plate 3 x 3 Cut Corner
×2
Plate Special 1 x 2 Side Handle [Free Ends]
×2
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×2
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×2
Technic Brick 1 x 10 [9 Pin Holes]
×2
Lever Small Base with Black Lever
×2
Brick 2 x 4
×2
Brick 1 x 4
×2
Brick 2 x 2 x 3
×2
Plate 2 x 3
×2
Plate 2 x 2
×2
Plate 1 x 2
×2
Plate 1 x 2
×2
Plate 1 x 1
×2
Plate 1 x 1
×2
Plate 6 x 10
×2
Propeller 3 Blade 9 Diameter
×2
Brick Special 1 x 4 with 4 Studs on One Side
×2
Tile 2 x 2 with Groove
×2
Tile 2 x 2 with Groove
×2
Tile 1 x 2 with Groove
×2
Tile 1 x 2 with Groove
×2
Tile 1 x 1 with Groove
×2
Tile 1 x 1 with Groove
×2
Technic Brick 1 x 2 [2 Pin Holes]
×2
Technic Pin Long with Friction Ridges Lengthwise and Stop Bush [3 Lateral Holes, Big Pin Hole]
×2
Technic Brick 1 x 2 with Axle Hole Type 1 [+ Opening] and Bottom Pin
×2
Plate 1 x 8
×2
Plate 1 x 8
×2
Plate 1 x 8
×2
Brick 1 x 3
×2