
Mission 1: Jetpack Pursuit
미니피규어 (2)
부품 목록 (56)

Tile Special 1 x 1 with Clip and Straight Tips
×3
Technic Pin with Friction Ridges Lengthwise and Center Slots
×3
Plate 2 x 2
×3
Technic Pin Long without Friction Ridges
×3
Technic Pin 1/2
×3
Plate 1 x 2
×2
Plate 1 x 2
×2
Technic Brick 1 x 2 [2 Pin Holes]
×2
Technic Pin Long with Friction Ridges Lengthwise and Stop Bush [3 Lateral Holes, Big Pin Hole]
×2
Plate 1 x 3
×2
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×2
Large Figure Weapon Blade, Ice Skate / Ice Blade Half
×2
Tail Shuttle - Small
×2
Bracket 1 x 2 - 2 x 2
×2
Tap 1 x 1 with Hole in Spout
×2
Tap 1 x 1 with Hole in Spout
×2
Wheel 18 x 14 with Pin Hole, Fake Bolts and Shallow Spokes
×2
Plate Special 1 x 4 with Angled Tubes
×2
Technic Brick 1 x 1 with Pin Hole
×2
Flexible Hose 8.5L with Tabbed Ends (Ends same color as Tube)
×2
Tile Special 1 x 2 Grille with Bottom Groove
×1
Tile Special 1 x 2 Grille with Bottom Groove
×1
Tile Special 1 x 2 with Handle
×1
Technic Brick 1 x 10 [9 Pin Holes]
×1
Handlebars
×1
Brick Round 2 x 2 x 1 2/3 Dome Top, Blocked Open Stud
×1
Rock 1 x 1 Jewel / Gem 24 Facet
×1
Plate 2 x 3
×1
Propeller 3 Blade 9 Diameter
×1
Bar 1 x 8 with Brick 1 x 2 Curved Top End (Axle Holder Inside Small End)
×1
Hook with Towball
×1
Hinge 1 x 2 Locking with 2 Fingers and Towball Socket, 9 Teeth
×1
Hinge Cylinder 1 x 2 Locking with 1 Finger and Axle Hole On Ends
×1
Tile 1 x 2 with Groove
×1
Tile 1 x 2 with Avionics Copper, Red & Silver Controls Print
×1
Technic Brick 1 x 2 [2 Pin Holes]
×1
Technic Pin Connector Plate with One Hole (Single on Bottom)
×1
Technic Brick 1 x 2 [1 Pin Hole]
×1
Slope Inverted 33° 3 x 2, Connections between Studs, Ovoid Bottom Pin
×1
Technic Axle Pin without Friction Ridges Lengthwise
×1
Technic Brick 1 x 6 [5 Pin Holes]
×1
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×1
Hinge Cylinder 1 x 3 Locking with 1 Finger and Technic Friction Pin with Round Hole
×1
Slope 33° 3 x 1
×1
Tread Small (20 Links)
×1
Hinge Plate 1 x 2 Locking with 2 Fingers On End, with Groove, 9 Teeth
×1
Bracket 1 x 2 - 2 x 2
×1
Dish 2 x 2 Inverted [Radar]
×1
Wedge Sloped 45° 2 x 4 Triple
×1
Technic Pin Connector Hub Perpendicular 3L with 4 Pins
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Wedge Sloped 6 x 4 Cutout, Stud Notches
×1
Sticker Sheet for Set 8631-1
×1
Technic Pin with Friction Ridges Lengthwise and Center Slots
×1
Technic Pin 1/2
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
