
Chopper Force
미니피규어 (1)
부품 목록 (91)

Technic Pin with Friction Ridges Lengthwise and Center Slots
×29
Technic Axle 2 Notched
×11
Technic Pin Long with Friction Ridges Lengthwise, 2 Center Slots
×8
Technic Axle Pin without Friction Ridges Lengthwise
×7
Technic Axle and Pin Connector Angled #1
×6
Technic Axle 4
×6
Technic Brick 1 x 12 [11 Pin Holes]
×6
Technic Pin 1/2
×6
Plate Round 1 x 1 with Solid Stud
×6
Technic Axle and Pin Connector Perpendicular
×6
Technic Pin Connector Round [No Slot]
×6
Brick Round 1 x 1 Open Stud
×5
Technic Bush
×5
Technic Axle 3
×5
Technic Slope Short (Wing Front)
×4
Technic Pin 3/4
×4
Wheel with Split Axle hole
×4
Tyre Offset Tread 24 x 8
×4
Technic Brick 1 x 4 [3 Pin Holes]
×4
Technic Brick 1 x 8 [7 Pin Holes]
×4
Plate 1 x 4
×4
Technic Gear 16 Tooth with Round Holes [Old Style]
×4
Brick Special 1 x 1 with Headlight
×4
Technic Bush 1/2 Toothed Type II [X Opening]
×4
Technic Gear 12 Tooth Bevel
×4
Wedge Plate 3 x 3 Cut Corner
×3
Tile 1 x 1 with Groove
×3
Plate 1 x 3
×3
Technic Gear 8 Tooth
×3
Slope Inverted 45° 2 x 1
×3
Technic Brick 1 x 2 [1 Pin Hole]
×3
Technic Axle 8
×3
Technic Brick 1 x 6 [5 Pin Holes]
×3
Technic Axle Connector Ridged [with x Hole x Orientation]
×3
Technic Plate 1 x 5 with Toothed Ends, 2 Studs and Center Axle Hole
×2
Technic Slope Short (Wing Front)
×2
Technic Beam 1 x 4 Thin with Stud Connector
×2
Technic Engine Crankshaft Center
×2
Technic Beam Triangle Thin [Type I]
×2
Technic Beam Triangle Thin [Type I]
×2
Plate 1 x 2
×2
Tile 1 x 2 with Groove
×2
Tile 1 x 2 with Groove
×2
Technic Axle and Pin Connector Angled #5 - 112.5°
×2
Technic Axle and Pin Connector Angled #3 - 157.5°
×2
Technic Beam 1 x 5 Thin
×2
Plate 1 x 8
×2
Technic Gear 24 Tooth Crown with Reinforcements [New Style]
×2
Brick Arch 1 x 4
×2
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×2
Plate 1 x 6
×2
Slope 65° 2 x 2 x 2 Smooth without Bottom Tube
×2
Technic Brick 1 x 2 [1 Pin Hole]
×2
Technic Plate 2 x 4 [3 Holes]
×2
Plate 1 x 4
×2
Plate 1 x 4
×2
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×2
Plate 2 x 16
×2
Slope 33° 3 x 1
×2
Slope 33° 3 x 1
×2
Slope Inverted 34° 3 x 1 without Internal Stopper
×2
Engine Smooth Large, Cone Back [1 x 2 Thin Top Plate]
×2
Engine Centre - Smooth Large
×2
Plate Round 1 x 1 with Solid Stud
×2
Technic Axle and Pin Connector Perpendicular
×2
Technic Axle Connector Ridged [with x Hole x Orientation]
×2
Technic Pin with Friction Ridges Lengthwise and Towball
×2
Technic Changeover Catch - + opening
×2
Technic Pin Connector Round [No Slot]
×2
Wing, Tail 4 x 1 x 3
×1
Slope Inverted 45° 3 x 1 Double with 2 Completely Open Studs
×1
Technic Plate Rotor 3 Blade with Toothed Ends and 3 Studs (Propeller)
×1
Technic Seat / Chair [3 x 2 Base]
×1
Plate 1 x 2
×1
Technic Plate 2 x 6 [5 Holes]
×1
Slope 33° 3 x 4
×1
Plate Round 1 x 1 with Towball and Hexagonal Hole [Maxifig Hand]
×1
Technic Brick 1 x 4 [3 Pin Holes]
×1
Technic Brick 1 x 4 [3 Pin Holes]
×1
Technic Brick 1 x 4 [3 Pin Holes]
×1
Technic Brick 1 x 16 [15 Pin Holes]
×1
Technic Axle 6
×1
Technic Plate 2 x 4 [3 Holes]
×1
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×1
Slope 33° 3 x 1
×1
Plate Round 1 x 1 with Solid Stud
×1
Plate Round 1 x 1 with Solid Stud
×1
Plate Round 1 x 1 with Solid Stud
×1
Technic Gear Rack 1 x 10 with Holes
×1
Sticker Sheet for Set 8232-1
×1
Rubber Band Small 13mm (Square Cross Section)
×1