
Kraang Lab Escape
미니피규어 (2)
부품 목록 (50)

Plate Round 1 x 1 with Solid Stud
×11
Antenna 1 x 4 with Rounded Top
×4
Large Figure Weapon Claw, with Clip
×4
Plate 1 x 2
×3
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×3
Slope Curved 4 x 1 Double with No Studs
×3
Bracket 1 x 2 - 1 x 2 Inverted
×3
Plate Special 1 x 2 with Pin Hole on Top
×2
Brick Special 1 x 2 with Pin
×2
Plate 4 x 6
×2
Plate 1 x 4
×2
Cone 1 x 1 [Top Groove]
×2
Cone 1 x 1 [Top Groove]
×2
Plate Round 4 x 4 with Pin Hole
×2
Brick Special 1 x 1 with Clip Vertical [Open O Clip, Hollow Stud]
×2
Plate Special 1 x 2 with Handle on End [Closed Ends]
×2
Technic Pin 1/2 with 2L Bar Extension
×2
Plate Special 1 x 2 with Clip Horizontal on End
×2
Hose Rigid 3mm D. 3L / 2.4cm
×2
Tile Round 1 x 1 with Gauge and Red Pointer Print
×2
Creature, The Kraang
×1
Plate Special 2 x 2 with Pin on Bottom
×1
Plate Special 2 x 2 with 2 Pin Holes
×1
Lever Small Base with Black Lever
×1
Plate 2 x 3
×1
Plate 2 x 2
×1
Slope 45° 2 x 2 with Green Radar, Green/Red Buttons and Disk Slot Print
×1
Technic Plate 2 x 6 [5 Holes]
×1
Brick 1 x 3
×1
Minifig Head [Plain] [Hollow Stud]
×1
Plate Special 1 x 2 with Handles [Flat Ends / Low Attachment]
×1
Brick Round 2 x 2 with Axle Hole
×1
Brick Special 1 x 1 with Headlight
×1
Tile Round 2 x 2 with Bottom Cross
×1
Tile Round 2 x 2 with Pizza Print
×1
Dish 6 x 6 Inverted, Radar / Webbed [Anti-studs at 90°]
×1
Dish 2 x 2 Inverted [Radar]
×1
Panel 1 x 2 x 1 [Rounded Corners]
×1
Windscreen 6 x 6 x 3 Canopy Half Sphere with Dual 2 Fingers
×1
Weapon Mace / Flail Spiked
×1
Plate Special 2 x 2 with Bar Frame Octagonal, Reinforced, Completely Round Studs
×1
Cylinder Half 2 x 4 x 5 with 1 x 2 cutout
×1
Tile 2 x 4 with Groove
×1
Plate Special 2 x 2 with Groove and Center Stud (Jumper)
×1
Chain 6L [5 Links]
×1
Hinge Tile 1 x 4 Locking Dual 1 Fingers on Top [8 Locking Ridges]
×1
Lever Small Base with Black Lever
×1
Plate Round 1 x 1 with Solid Stud
×1
Hose Rigid 3mm D. 3L / 2.4cm
×1
Tile Round 1 x 1 with Gauge and Red Pointer Print
×1
