
Angler Ambush
미니피규어 (2)
부품 목록 (66)

Plate 1 x 2
×11
Plate Special 1 x 1 with Clip Vertical [Thick U Clip]
×10
Animal Body Part, Barb / Claw / Tooth / Talon / Horn, Small
×8
Plate Special 1 x 2 Side Handle [Free Ends]
×5
Slope 45° 2 x 1 with Bottom Pin
×4
Plate 2 x 6
×4
Wedge Sloped 45° 2 x 4 Triple
×4
Minifig Footwear Flipper [Thin]
×4
Plate Special 1 x 1 with Clip Horizontal [Thick U Clip]
×4
Plate 2 x 2
×3
Tile 1 x 2 with Groove
×3
Brick 2 x 2 Corner
×2
Plate 2 x 2 Corner
×2
Technic Axle Towball
×2
Weapon Spear Gun with Rounded Trigger and Thin Spear Base
×2
Brick Special 1 x 4 with 4 Studs on One Side
×2
Technic Brick 1 x 2 [2 Pin Holes]
×2
Engine - Smooth, Small 1 x 2 Side Plate [With Axle Holders]
×2
Animal Body Part / Plant, Tail / Claw / Horn / Branch / Tentacle, End Section
×2
Flag 2 x 2 Trapezoid with Flat Area between Clips
×2
Flag 2 x 2 Trapezoid with Flat Area between Clips
×2
Wedge Curved 4 x 4 No Top Studs
×2
Wedge Plate 3 x 6 Cut Corners
×1
Equipment Whip [aka Plant Vine]
×1
Tile Special 1 x 1 with Clip and Straight Tips
×1
Tile Special 1 x 1 with Clip and Straight Tips
×1
Handlebars
×1
Plant, Sea Grass
×1
Plate 2 x 4
×1
Plate 2 x 3
×1
Tool Jackhammer / Motor Hammer
×1
Plate 1 x 1
×1
Plate 4 x 6
×1
Plate 2 x 8
×1
Hinge Cylinder 1 x 2 Locking with 2 Click Fingers and Axle Hole, 9 Teeth
×1
Slope 2 x 2 No Studs, with 3 Side Pistons Raised Edges
×1
Tile 2 x 2 with Groove
×1
Tile 1 x 1 with Groove
×1
Technic Axle and Pin Connector Angled #2 - 180°
×1
Technic Pin Long without Friction Ridges - Single Slot
×1
Technic Brick 1 x 2 [1 Pin Hole]
×1
Plate 1 x 4
×1
Slope Inverted 33° 3 x 2, No Connections between Studs, Ovoid Bottom Pin
×1
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×1
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×1
Plate Special 1 x 2 with Handles [Flat Ends / Low Attachment]
×1
Technic Axle Pin with Friction Ridges Lengthwise
×1
Brick Curved 6 x 2
×1
Hinge Plate 1 x 2 Locking with 1 Finger on Side, with Groove
×1
Slope 75° 2 x 1 x 3 with Open Stud
×1
Tail Shuttle, Small with Double-Sided Black Trident and Sub Deep Diving Print
×1
Cone 1 x 1 [No Top Groove]
×1
Cone 1 x 1 [No Top Groove]
×1
Brick Curved 2 x 2 x 2/3 Two Studs and Curved Slope End
×1
Brick Curved 2 x 2 x 2/3 Two Studs and Curved Slope End
×1
Wedge Sloped 45° 2 x 4 Triple with Angler Fish Face Print
×1
Wedge Plate 3 x 4 with Stud Notches
×1
Plate Special 1 x 2 [Side Handle Closed Ends]
×1
Panel 1 x 2 x 1 [Square Corners]
×1
Money / Coin with "10" Sans-serif Type
×1
Money / Coin with "20" Sans-serif Type
×1
Money / Coin with "30" Sans-serif Type
×1
Money / Coin with "40" Sans-serif Type
×1
Tile 1 x 1 with Groove
×1
Technic Axle Pin with Friction Ridges Lengthwise
×1
Animal Body Part, Barb / Claw / Tooth / Talon / Horn, Small
×1
