
Dozer
미니피규어 (1)
부품 목록 (101)

Technic Link Tread Wide with Two Pin Holes
×58
Tile Special 1 x 2 Grille with Bottom Groove
×9
Plate Special 4 x 4 with Studs on One Edge [Plain]
×9
Brick Special 1 x 2 with Grille
×7
Brick 1 x 4
×7
Technic Brick 1 x 2 [1 Pin Hole]
×7
Brick Round 2 x 2 with Axle Hole
×7
Brick Special 1 x 2 with Pin
×6
Brick Special 1 x 2 with Handle
×6
Plate 1 x 1
×6
Plate 1 x 6
×6
Plate 1 x 4
×6
Plate 2 x 6
×6
Slope 75° 2 x 1 x 3 with Hollow Stud
×6
Slope Curved 2 x 2 No Studs - 3 Recessed Side Ports
×6
Slope 18° 2 x 1 x 2/3 with 4 Slots / Grate
×6
Bracket 1 x 2 - 1 x 4 [Square Corners]
×5
Fence Lattice 1 x 4 x 2
×5
Plate 2 x 3
×4
Plate 1 x 2
×4
Brick Special 1 x 4 with 4 Studs on One Side
×4
Technic Brick 1 x 2 [2 Pin Holes]
×4
Technic Pin 3/4
×4
Technic Beam 1 x 3 Thick
×4
Technic Pin Connector Plate 1 x 2 x 1 2/3 [Two Holes On Top]
×4
Brick 1 x 3
×4
Slope Inverted 45° 2 x 1
×4
Technic Pin without Friction Ridges Lengthwise
×4
Plate Special 1 x 1 with Clip Vertical [Thick U Clip]
×4
Wheel 11 x 8 with Center Groove
×4
Plate 1 x 10
×4
Technic Pin Connector Hub Perpendicular 3L with 4 Pins
×4
Technic Tread Sprocket Wheel Large 10 Tooth
×4
Light Cover 1 x 1 Round with Internal Bar / Bionicle Barraki Eye
×4
Technic Axle 5.5 with Stop [Rounded Short End]
×4
Plate Special 4 x 6 with Studs on 3 Edges
×4
Brick Special 2 x 2 with Pin and Axle Hole
×4
Brick 2 x 6
×3
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×3
Lever Small Base with Black Lever
×3
Plate 4 x 8
×3
Plate 1 x 4
×3
Hinge Plate 1 x 4 Locking Dual 1 Finger
×3
Hinge Plate 3 x 4 Locking Dual 2 Finger, 9 Teeth
×3
Plate Special 1 x 2 [Side Handle Closed Ends]
×3
Panel 1 x 2 x 3 - Solid Studs
×2
Tile 1 x 4 with Groove
×2
Brick 1 x 8
×2
Plate 2 x 4
×2
Plate 1 x 2
×2
Plate 4 x 4
×2
Brick Round 1 x 1 Open Stud
×2
Technic Brick 1 x 14 [13 Pin Holes]
×2
Technic Axle Connector with Axle Hole
×2
Technic Pin Long with Friction Ridges Lengthwise and Stop Bush [3 Lateral Holes, Big Pin Hole]
×2
Technic Axle 2 Notched
×2
Technic Brick 1 x 2 with Axle Hole Type 1 [+ Opening] and Bottom Pin
×2
Technic Brick 1 x 4 [3 Pin Holes]
×2
Slope Inverted 33° 3 x 2, Connections between Studs, Ovoid Bottom Pin
×2
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×2
Plate 6 x 6
×2
Plate Special 2 x 4 Thin 4 Holes, Struts and 2 Pins [Undercarriage]
×2
Technic Axle Pin with Friction Ridges Lengthwise
×2
Slope 45° 2 x 8
×2
Engine Centre - Smooth Large
×2
Slope Curved 3 x 1 No Studs
×2
Technic Axle and Pin Connector, Perpendicular with Extension
×2
Crane Harbor Derrick 16 with Double Attachment
×2
Plate Special 1 x 2 with Clips Horizontal [Thick U-Clips]
×2
Technic Engine Block Half / Side Intake Panel
×2
Bar 6L with Stop Ring
×2
Technic Axle 1.5 with Perpendicular Axle Connector (Technic Pole Reverser Handle)
×2
Tile 1 x 6 with Groove
×2
Tile Special 1 x 2 with Handle
×1
Brick 2 x 8
×1
Brick Curved 2 x 2, Two Top Studs
×1
Plate 4 x 6
×1
Plate 6 x 8
×1
Slope 45° 2 x 4
×1
Slope 45° 2 x 2 with Green Radar, Green/Red Buttons and Disk Slot Print
×1
Door 1 x 3 x 2 Right
×1
Door 1 x 3 x 2 Left
×1
Wedge Plate 4 x 6 Cut Corners
×1
Technic Axle Pin without Friction Ridges Lengthwise
×1
Seat / Chair 2 x 2
×1
Propeller 8 Blade 5 Diameter
×1
Wedge 4 x 2 Right
×1
Wedge 4 x 2 Left
×1
Panel 1 x 4 x 3 [Hollow Studs]
×1
Panel 1 x 4 x 3 [Hollow Studs]
×1
Wedge Plate 8 x 3, 22° Right
×1
Wedge Plate 8 x 3, 22° Left
×1
Slope Curved 4 x 6 x 2/3 Triple Curved with 4 Studs
×1
Fence 1 x 8 x 2 2/3
×1
Plate Special 6 x 12 with Studs on 3 Edges
×1
Equipment Telescope / Torch / Spyglass, Support Round 1 x 1 x 1 2/3
×1
Sticker Sheet for Set 7685-1
×1
Lever Small Base with Black Lever
×2
Technic Pin 3/4
×1
Technic Pin without Friction Ridges Lengthwise
×1