
Norbert: Hagrid's Baby Dragon
부품 목록 (149)

Hinge Cylinder 1 x 2 Locking with 1 Finger and Axle Hole On Ends [No Side Slots]
×2
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×2
Brick Round 2 x 2 D. Tube with 45° Elbow and Axle Holes (Crossholes) at Each End [LONG]
×2
Hinge Cylinder 1 x 2 Locking with 2 Click Fingers and Axle Hole, 7 Teeth
×2
Brick Curved 1 x 2 x 1 with Curved Top
×2
Cone 1 x 1 [Top Groove]
×2
Cone 1 x 1 [Top Groove]
×2
Plate Special 2 x 4 with Groove and Two Center Studs (Jumper)
×2
Technic Axle 1.5 with Perpendicular Axle Connector (Technic Pole Reverser Handle)
×2
Bracket 1 x 1 - 1 x 2 Inverted
×2
Plate 1 x 5
×2
Tile 3 x 3 Curved, Macaroni
×2
Plate Round Corner 2 x 2 with 1 x 1 Cutout
×2
Plate Round Corner 2 x 2 with 1 x 1 Cutout
×2
Brick Special 1 x 2 x 1 1/3 with Rotation Joint Socket
×2
Plate Round 1 x 1 with Open Stud
×2
Bracket 1 x 2 - 2 x 2 Inverted
×2
Tile Special 1 x 2 with Sloped Walls AKA Money / Gold Bar [Ingot]
×2
Bracket 5 x 2 x 1 1/3 with Holes, Pin Bottom
×1
Foil Sheet for Set 76477-1, Dragon Wings
×1
Tile Special 1 x 1 with Clip with Rounded Edges
×1
Slope 45° 2 x 1 Inverted with 2/3 Cutout
×1
Plate Special 1 x 1 Rounded with Handle
×1
Plate 2 x 8
×1
Slope 45° 2 x 1 Double / Inverted with Bottom Stud Holder
×1
Tile 1 x 1 with Groove
×1
Technic Brick 1 x 2 with Axle Hole Type 1 [+ Opening] and Bottom Pin
×1
Bracket 1 x 1 - 1 x 1
×1
Technic Brick 1 x 2 [1 Pin Hole]
×1
Technic Plate 2 x 8 [7 Holes]
×1
Brick Round 2 x 2 with Axle Hole
×1
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×1
Animal Body Part / Plant, Tail / Claw / Horn / Branch / Tentacle, End Section
×1
Brick Special 1 x 1 with Studs on 2 Sides
×1
Plate Special 1 x 1 with Tooth
×1
Brick Special 1 x 2 with Studs on 2 Sides
×1
Animal Body Part / Plant, Tail / Neck / Branch / Trunk, Middle Section with Pin Holes
×1
Cone 1 x 1 [Top Groove]
×1
Technic Pin with Friction Ridges Lengthwise with No Center Slots
×1
Plate Round 1 x 1 with Solid Stud
×1
Bar, Angled with 1 x 1 Round Plate / Stud on End
×1
Animal / Creature Body Part, Tail / Claw / Horn / Branch / Tentacle, End Section, Large
×1
Tile 2 x 6
×1
Bracket 1 x 1 - 1 x 2 Inverted
×1
Bar 2L with Stop in Center
×1
Plate Round 1 x 1 with Open Stud
×1
Wave / Flame Rounded Large [Plain]
×1
Plate 1 x 1 x 2/3 with Open Stud
×1
Slope Curved 4 x 1 Double with No Studs
×1