
Hulkbuster
미니피규어 (1)
부품 목록 (588)

Slope 75° 2 x 2 x 3 [Solid Studs]
×2
Large Figure Weapon, Barrel with 2 Pin Holes and 3 Axle Holes
×2
Spoiler 2 x 4 with Handle [Plain]
×2
Technic Axle and Pin Connector Perpendicular Double 4L
×2
Pneumatic Hose Connector with Axle Connector
×2
Plate Special 2 x 2 x 2/3 with Two Studs On Side and Two Raised [Solid Anti-stud]
×2
Tile Special 1 x 2 with Sloped Walls AKA Money / Gold Bar [Ingot]
×2
Technic Beam Triangle Thin [Type II]
×2
Bracket 1 x 2 - 1 x 2 Inverted
×2
Bracket 1 x 2 - 1 x 2 Inverted
×2
Bracket 1 x 2 - 1 x 2
×2
Sticker Sheet for Set 76210-1
×1
Windscreen 6 x 13 x 2
×1
Tile Round 2 x 2 with Hole
×1
Plate Round Corners 2 x 6 Double
×1
Plate Special 2 x 4 Fresnel Lens
×1
Brick Special 1 x 2 x 1 2/3 with 4 Studs on 1 Side
×1
Wedge Plate 2 x 2 Left
×1
Wedge Plate 2 x 2 Right
×1
Plate 2 x 12
×1
Technic Pin Connector Hub with 2 Axles
×1
Slope Curved 2 x 1 with Stud Notch Right
×1
Slope Curved 2 x 1 with Stud Notch Left
×1
Plate 2 x 4
×1
Plate 1 x 2
×1
Slope 45° 2 x 2
×1
Tile 1 x 2 with Groove
×1
Technic Beam 1 x 15 Thick
×1
Technic Ball Joint
×1
Plate 1 x 8
×1
Plate 1 x 6
×1
Plate 1 x 4
×1
Plate Special 1 x 2 with Handles [Flat Ends / Low Attachment]
×1
Technic Brick 1 x 12 [11 Pin Holes]
×1
Tool Screwdriver and Spanner / Wrench
×1
Tile 1 x 8 with Groove
×1
Plate 1 x 10
×1
Slope 10° 6 x 8
×1
Tool Hammer / Mallet Large
×1
Wedge Plate 6 x 4 Right
×1
Wedge Plate 6 x 4 Left
×1
Plate Special 1 x 2 [Side Handle Closed Ends]
×1
Wedge Curved 10 x 3 Left
×1
Wedge Curved 10 x 3 Right
×1
Wedge Plate 6 x 3 Right
×1
Wedge Plate 6 x 3 Left
×1
Technic Axle Connector Smooth [with x Hole + Orientation]
×1
Cone 1 x 1 [Top Groove]
×1
Technic Axle 3 with Stud
×1
Bracket 5 x 2 x 2 1/3 with Holes, Inside Stud Holder
×1
Tile 2 x 4 with Groove
×1
Bar 3L
×1
Tile 8 x 16 with Bottom Tubes
×1
Plate Special 4 x 6 with Trap Door Hinge [Long Pins]
×1
Brick Arch 1 x 6 Raised Arch
×1
Windscreen 10 x 10 x 5 Dome with Dual 2 Fingers with Hulk Buster Face/Mask print
×1
Brick and Axle Separator v2.0
×1
Spoiler 2 x 4 with Handle [Plain]
×1
Technic Pin with Friction Ridges Lengthwise with No Center Slots
×4
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×3
Plate Round 1 x 1 with Solid Stud
×3
Plate 1 x 1
×2
Plate 1 x 1
×2
Tile 1 x 1 with Groove
×2
Technic Bush 1/2 Smooth with Axle Hole Semi-Reduced
×2
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×2
Technic Pin Connector Round 1L [Beam]
×1
Technic Pin Connector Round 1L [Beam]
×1
Technic Pin Connector Round 1L [Beam]
×1
Tile Round 1 x 1 Quarter
×1
Tile Round 1 x 1 Quarter
×1
Tile Round 1 x 1 Quarter
×1
Plate 1 x 1
×1
Plate 1 x 1
×1
Tile 1 x 1 with Groove
×1
Tile 1 x 1 with Groove
×1
Tile 1 x 1 with Groove
×1
Technic Pin 1/2
×1
Dish 2 x 2 Inverted [Radar]
×1
Bar 1L with Clip [Cut Edges and One Side Hole] [Gap in Clip]
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Plate Round 1 x 1 with Solid Stud
×1
Plate Round 1 x 1 with Solid Stud
×1
Plate Round 1 x 1 with Open Stud
×1
Bar 3L
×1
Technic Pin 1/2 with Friction
×1
Tile Round 1 x 1
×1