
AT-ST Walker
미니피규어 (1)
부품 목록 (355)

Technic Beam 1 x 3 Thick
×2
Technic Beam 1 x 11 Thick
×2
Slope Curved 2 x 2 x 2/3 Inverted
×2
Plate Round 1 x 1 with Hollow Stud and Horizontal Bar 1L
×2
Plate Special 2 x 2 with Only 2 studs
×2
Equipment Paint Roller Brush Handle Smooth Handle
×2
Plate 1 x 3
×2
Plate 1 x 6
×2
Technic Brick 1 x 2 [1 Pin Hole]
×2
Technic Brick 1 x 2 [1 Pin Hole]
×2
Technic Brick 1 x 8 [7 Pin Holes]
×2
Technic Plate 2 x 8 [7 Holes]
×2
Technic Brick 1 x 12 [11 Pin Holes]
×2
Hinge Brick 1 x 2 Base
×2
Hinge Brick 1 x 2 Top Plate Thin
×2
Brick Round 2 x 2 with Axle Hole
×2
Dish 8 x 8 Inverted [Radar], Solid Studs, Squared Anti-stud Underside
×2
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×2
Technic Beam 1 x 9 Thick
×2
Door Frame 1 x 4 x 4, no Holes
×2
Bracket 2 x 2 with 1 x 2 Vertical Studs
×2
Wedge Curved 6 x 2 Left, Inner Ridges
×2
Wedge Curved 8 x 3 x 2 Open Right
×2
Wedge Curved 8 x 3 x 2 Open Left
×2
Wedge Plate 4 x 2 Right
×2
Wedge Plate 4 x 2 Left
×2
Technic Axle and Pin Connector Perpendicular 3L with 2 Pin Holes
×2
Technic Axle Connector with Axle Hole [Reinforced]
×2
Slope Inverted 33° 3 x 1 with Internal Stopper and No Front Stud Connection
×2
Plate Special 2 x 2 x 2/3 with Two Studs On Side and Two Raised [Half Hollow Anti-stud] - Updated Version
×2
Technic Axle Connector Double Flexible [Rubber]
×2
Plate Special 1 x 2 with Long Stud Receptacle (Space Wing)
×2
Tap 1 x 1 without Hole in Spout
×2
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×2
Hinge Plate 1 x 2 Locking with 2 Fingers On End, without Groove, 7 Teeth
×2
Technic Axle 8 with Stop
×2
Wedge Curved 6 x 2 Right, Smooth Inner Walls
×2
Plate Special 1 x 2 with Clips Horizontal [Open O Clips]
×2
Plate Round 4 x 4 with Pin Hole
×2
Slope 18° 4 x 1
×2
Plate Special 1 x 2 with Handle on End [Closed Ends]
×2
Plate 1 x 12
×2
Plate 1 x 12
×2
Plate Special 1 x 1 with Clip Vertical [Thick Open O Clip]
×2
Plate Round 1 x 1 with Solid Stud
×2
Turntable 4 x 4 Square Base, Locking
×2
Plate Special 1 x 2 with Clip Horizontal on End
×2
Plate Special 1 x 2 with Clip Horizontal on End
×2
Technic Beam 1 x 11 Thick with Alternating Holes
×2
Bracket 1 x 1 - 1 x 2 Inverted
×2
Plate 3 x 3 Corner
×2
Bracket 1 x 1 - 1 x 2
×2
Tile 2 x 4 with Groove
×2
Brick Round 4 x 4 Centre Hole
×2
Panel 1 x 2 x 2 [Side Supports / Hollow Studs]
×2
Panel 1 x 2 x 2 [Side Supports / Hollow Studs]
×2
Bar 3L
×2
Plate Special 1 x 2 with Bar Up [Horizontal Arm 5mm]
×2
Arm Skeleton [Bent / 2 Clips]
×2
Tile Special 1 x 2 with Sloped Walls AKA Money / Gold Bar [Ingot]
×2Sticker Sheet for Set 75417-1
×1
Wheel 18 x 8 with Fake Bolts and Deep Spokes with Inner Ring
×1
Tile 1 x 4 with Groove
×1
Plate 2 x 12
×1
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×1
Tile 4 x 4 Curved, Macaroni
×1
Brick 2 x 2
×1
Brick 1 x 8
×1
Brick 1 x 4
×1
Plate 2 x 4
×1
Plate 2 x 4
×1
Plate 2 x 4
×1
Plate 2 x 3
×1
Plate 4 x 10
×1
Plate 4 x 6
×1
Plate 2 x 8
×1
Plate 4 x 8
×1
Slope 45° 2 x 4
×1
Brick Special 1 x 4 with 4 Studs on One Side
×1
Tile 1 x 2 with Stylised Computer Console Print
×1
Tile 1 x 2 with Controls, Slides, Joystick print
×1
Technic Brick 1 x 2 [2 Pin Holes]
×1
Plate Special 1 x 3 with 2 Studs with Groove and Inside Stud Holder (Jumper)
×1
Wedge Sloped 2 x 5 Left
×1
Wedge Sloped 2 x 5 Right
×1
Plate 1 x 6
×1
Technic Axle 8
×1
Technic Plate 2 x 4 [3 Holes]
×1
Technic Bush
×1
Plate 2 x 10
×1
Brick Round 2 x 2 with Axle Hole
×1
Plate 6 x 6
×1
Wheel 11 x 8 with Center Groove
×1
Plate 2 x 16
×1
Wedge Plate 3 x 2 Right
×1
Wedge Plate 3 x 2 Left
×1
Tyre 43.2 x 22 ZR
×1
Plate 1 x 10
×1
Plate Special 1 x 4 Offset with Bar Holes
×1
Wedge Plate 8 x 3, 22° Right
×1