
Imperial Probe Droid
부품 목록 (216)

Plate Round 1 x 1 with Open Stud
×68
Plate 1 x 2
×17
Plate Special 1 x 2 with Clip Horizontal on End
×17
Plate Round 1 x 1 with Hollow Stud and Horizontal Bar 1L
×15
Bar 3L
×15
Tile 1 x 2 with Groove
×14
Plate Special 1 x 2 Rounded with 2 Open Studs
×14
Plate Special 3 x 2 with Rounded End, Hole
×12
Brick Round 2 x 2 with Axle Hole
×11
Plate Special 1 x 2 with Clips Horizontal [Open O Clips]
×11
Slope Curved 2 x 1 with Stud Notch Left
×10
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×10
Plate Round 1 x 1 with Open Stud
×10
Tile Special 1 x 1 with Clip with Rounded Edges
×8
Plate 2 x 2 Corner
×8
Plate Special 1 x 1 Rounded with Handle
×8
Tile 1 x 1 with Groove
×8
Slope 33° 3 x 2
×8
Cone 1 1/2 x 1 1/2 x 2/3
×8
Plate 1 x 3
×8
Equipment Candlestick
×8
Brick Special 1 x 1 with Headlight
×8
Plate Special 1 x 2 [Side Handle Closed Ends]
×8
Plate Special 1 x 1 with Clip Horizontal [Thick Open O Clip]
×8
Plate Round 1 x 1 with Open Stud
×8
Plate 2 x 2 Corner
×7
Plate 2 x 3
×7
Plate Round Corner 3 x 3
×7
Slope 45° 2 x 1 with Bottom Pin
×7
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×7
Slope 18° 4 x 1
×7
Plate Special 1 x 2 with 1 Stud with Groove and Inside Stud Holder (Jumper)
×6
Wedge Plate 3 x 3 Cut Corner
×6
Dish 2 x 2 Inverted [Radar]
×6
Slope 45° 2 x 1 with 2/3 Inverted Cutout and no stud
×5
Plate 2 x 3
×5
Wedge Plate 4 x 4 Cut Corner
×5
Plate 1 x 3
×5
Plate 1 x 4
×5
Brick Curved 1 x 2 x 1 No Studs
×5
Technic Pin 1/2
×5
Tile Round 1 x 1
×5
Bar Holder with Clip
×4
Slope Curved 2 x 2 x 2/3
×4
Slope Curved 2 x 2 x 2/3
×4
Tile Round 1 x 1 with Hollow Bar
×4
Plate Round Half 4 x 8
×4
Brick Round Corner 5 x 5 x 1 Curved, Bottom Cut Outs, No Studs, 7 Bottom Tubes
×4
Slope Curved 2 x 1 with Stud Notch Right
×4
Plate 2 x 4
×4
Plate 1 x 1
×4
Plate Round Corner 4 x 4
×4
Brick Round 1 x 1 Open Stud
×4
Plate 1 x 4
×4
Brick Special 1 x 1 with Headlight
×4
Slope 33° 3 x 1
×4
Tool Crank Shaft with Bar, Stud
×4
Plate Round Corner 3 x 3 with 2 x 2 Round Cutout
×4
Plate Special 2 x 2 with Groove and Center Stud (Jumper)
×4
Bar 3L
×4
Plate Round 6 x 6 with Hole
×3
Wedge Sloped 45° 2 x 2 Corner
×3
Plate Special Round 2 x 2 with Center Stud (Jumper Plate)
×3
Plate Special 1 x 2 with Pin Hole Underneath
×3
Technic Pin with Friction Ridges Lengthwise and Center Slots
×3
Slope Curved 2 x 1 with Stud Notch Right
×3
Slope Curved 2 x 1 with Stud Notch Left
×3
Brick 1 x 2
×3
Brick 1 x 4
×3
Plate 1 x 2
×3
Plate 1 x 1
×3
Plate 1 x 1
×3
Hinge Brick 1 x 2 Base
×3
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×3
Dish 3 x 3 Inverted [Radar]
×3
Tool Cup / Half Ball
×3
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×3
Light Cover 1 x 1 Round with Internal Bar / Bionicle Barraki Eye
×3
Hinge Brick 2 x 2 Top Plate Thin
×3
Brick Special 1 x 1 with Stud on 1 Side
×3
Technic Gear 8 Tooth [Reinforced]
×2
Slope Curved 2 x 1 No Studs [1/2 Bow]
×2
Slope Curved 2 x 1 No Studs [1/2 Bow]
×2
Slope Curved 4 x 1 Inverted
×2
Weapon Gun / Blaster 1 x 2 x 2/3 with Studs on Sides and Handle
×2
Brick Special 1 x 2 x 1 2/3 with 4 Studs on 1 Side
×2
Brick Special 1 x 2 x 1 2/3 with 4 Studs on 1 Side
×2
Plate Special 1 x 1 Rounded with Handle
×2
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×2
Brick 2 x 4
×2
Brick 1 x 2
×2
Plate 2 x 4
×2
Plate 2 x 3
×2
Plate 2 x 2
×2
Plate 1 x 2
×2
Bar 4L (Lightsaber Blade / Wand)
×2
Hinge Plate 1 x 2 Locking with 1 Finger On Top
×2
Brick Round 1 x 1 Open Stud
×2
Tile 1 x 2 with Groove
×2
Technic Plate 2 x 6 [5 Holes]
×2