
Kai's Source Dragon Battle
미니피규어 (4)

Wolf Mask Guard
fig-014566×1

Wolf Mask Warrior
fig-014577×1

Kai - Heavy Shoulder Guards
fig-014780×1

Wyldfyre, Shoulder Guard
fig-014782×1
부품 목록 (64)

Plate Special 1 x 2 [Open O Top Clip]
×6
Tile Round 2 x 2 with Bottom Stud Holder
×4
Plate Special 2 x 3 with Rocks
×4
Creature Body Part, Wing 11 x 6 with 3 Bars, Red Marble pattern
×4
Cone 1 x 1 [Top Groove]
×4
Plate 2 x 4
×3
Animal Body Part / Plant, Tail / Trunk / Tentacle / Tongue / Vine / Tree Branch (Long Tip)
×3
Wave / Flame Rounded Large with Marbled Trans-Orange Pattern
×3
Bar Holder with Clip
×2
Slope Curved 2 x 2 x 2/3
×2
Weapon Sword / Katana / Shamshir with Capped Pommel [Square Guard]
×2
Wheel Hard Plastic (37mm D. x 22mm), Pin Hole
×2
Plant, Leaves 4 x 3
×2
Plate 2 x 3
×2
Slope 33° 3 x 2
×2
Brick Special 1 x 2 with Vertical Closed Handle on Edge
×2
Plate Special 1 x 2 Rounded with 2 Open Studs
×2
Mudguard 2 x 4 with 2 x 2 Studs and Flared Wings
×2
Dish 2 x 2 Inverted [Radar]
×2
Wheel 11 x 12 with Hole Notched for Wheels Holder Pin
×2
Plate Special 1 x 2 with Clips Horizontal [Open O Clips]
×2
Animal Body Part, Barb / Claw / Tooth / Talon / Horn, Medium
×2
Wedge Plate 3 x 4 with Stud Notches [Reinforced Underside]
×2
Slope Curved 2 x 1 No Studs [1/2 Bow]
×1
Plate Special 1 x 2 5.9mm Centre Side Towball Socket
×1
Slope Curved 2 x 2 x 2/3
×1
Slope Curved 3 x 2 No Studs
×1
Tile Special 1 x 2 with Handle
×1
Brick 1 x 2
×1
Plate 2 x 3
×1
Plate 2 x 2
×1
Brick Special 1 x 2 with Vertical Clip [Open O Clip]
×1
Plate 2 x 8
×1
Slope 45° 2 x 2
×1
Brick 1 x 2 x 2 with Inside Stud Holder
×1
Technic Brick 1 x 2 [1 Pin Hole]
×1
Plate 1 x 4
×1
Plate Special 2 x 2 with Wheels Holder Wide [Reinforced Underside Type 2]
×1
Plate 8 x 8 with Rounded End
×1
Wedge Curved 6 x 4 Triple
×1
Hinge Plate 1 x 2 Locking with 1 Finger on Side, without Groove
×1
Projectile, Arrow with Shaft, Hollow Black Rubber End
×1
Plate Special 2 x 2 with Wheels Holder Wide - Technic Pins
×1
Weapon Sword with Jagged Edges and Trans-Red Flames pattern
×1
Launcher, Brick Special 2 x 6 Spring Shooter with Light Bluish Gray Top
×1
Wedge 3 x 4 [Stud Notches]
×1
Wedge Plate 2 x 4
×1
Animal Body Part, Dragon Head Long
×1
Hinge Plate 1 x 12 Locking with Angled Side Extensions and Tapered Ends, 7 Teeth
×1
Technic Pin with Friction Ridges Lengthwise with No Center Slots
×1
Wedge 4 x 4 Fractured Polygon Top
×1
Brick Special 4 x 10 x 1 With 2 Wedges, Pin Holes, 4 x 2 Recessed Center
×1
Plate Special 2 x 4 with Groove and Two Center Studs (Jumper)
×1
Mech Leg, Right, with Black Pin
×1
Mech Leg, Left, with Black Pin
×1
Creature Body Part, Dragon Head Upper Jaw with Bright Light Yellow Eyes, Dark Red/Black Markings print
×1
Technic Brick Special 1 x 2 with Pin Hole and 1 x 2 Plate
×1
Technic Pin with Friction, Bar 2L and Towball
×1
Slope 30° 1 x 2 x 2/3
×1
Slope 30° 1 x 2 x 2/3
×1
Brick Special 1 x 2 with 1 Center Stud on 1 Side, Bottom Stud Holder
×1
Slope Curved 4 x 1 Double with No Studs
×1
Weapon Pike / Spear Flat End
×1
Bracket 1 x 2 - 2 x 2 Inverted
×1