
Imperium Dragon Hunter Hound
미니피규어 (3)

Lloyd - Dragons Rising Robes
fig-013771×1

Imperium Claw General, Shoulder Guards
fig-013776×1

Jay - Dragons Rising Robes
fig-013786×1
부품 목록 (81)

Plate Special 1 x 2 Rounded with 2 Open Studs
×13
Creature Body Part, Barb Large (Claw, Talon) with Clip
×12
Plate Special 2 x 3 with Rocks
×12
Slope 45° 2 x 1 Triple with Inside Stud Holder
×11
Tile Special 1 x 1 with Clip with Rounded Edges
×8
Plate Special 1 x 2 5.9mm Centre Side Towball Socket
×6
Plate Special 2 x 2 with Towball and Hole
×5
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×5
Bar 3L
×5
Weapon Sword / Katana / Shamshir with Capped Pommel [Square Guard]
×4
Plate Special 4 x 4 with 3 x 3 Quarter Round Cutout
×4
Slope Inverted 45° 2 x 1
×4
Weapon Spike Flexible 3.5L
×4
Slope Curved 4 x 1 Double with No Studs
×4
Plate 2 x 3
×3
Brick Special 1 x 2 with 2 Studs on 1 Side
×2
Plate Special 1 x 2 with 5.9mm Centre Side Towball
×2
Plate Special 1 x 2 5.9mm Towball Socket
×2
Slope 45° 1 x 1 x 2/3 Quadruple Convex [Pyramid]
×2
Brick Special 1 x 2 x 1 2/3 with 4 Studs on 1 Side
×2
Plate Special 1 x 1 Rounded with Handle
×2
Slope 45° 2 x 1 with 2/3 Inverted Cutout and no stud
×2
Bracket 1 x 2 - 1 x 4 [Rounded Corners at Bottom, Square Corners at Top]
×2
Plate 2 x 4
×2
Plate 2 x 2
×2
Brick Round 1 x 1 Open Stud
×2
Wedge Plate 4 x 6 Cut Corners
×2
Technic Brick 1 x 2 with Axle Hole Type 1 [+ Opening] and Bottom Pin
×2
Hinge Plate 1 x 2 Locking with 1 Finger on Side, without Groove
×2
Hinge Plate 1 x 2 Locking with 2 Fingers On End, without Groove, 7 Teeth
×2
Brick Curved 1 x 2 x 1 1/3 with Curved Top
×2
Brick Special 1 x 2 x 1 2/3 with 8 Studs on 3 Sides
×2
Plate Angled 2 x 2 with Step and Hole in Center
×2
Brick Special 2 x 5 with Slope, Studs on Side
×2
Wedge Sloped 4 x 4 Triple with 3 Ridges on Slope
×2
Plate 1 x 1 x 2/3 with Open Stud
×2
Tile Special 1 x 2 with Sloped Walls AKA Money / Gold Bar [Ingot]
×2
Sticker Sheet for Set 71790-1
×1
Slope Curved 4 x 1 No Studs [Stud Holder with Symmetric Ridges]
×1
Slope Curved 4 x 1 Inverted
×1
Tile Special 1 x 2 with Two Vertical Teeth / Tooth
×1
Tile Round 2 x 2 with Hole
×1
Large Figure Weapon Lightsaber Hilt with Axle Hole and Two Bar Holders
×1
Plate Special 2 x 3 with Rocks
×1
Brick Round 2 x 2 Special with Spikes
×1
Technic Axle Towball
×1
Slope Curved 2 x 1 with Stud Notch Right
×1
Slope Curved 2 x 1 with Stud Notch Left
×1
Technic Brick 1 x 2 with Axle Hole Type 1 [+ Opening] and Bottom Pin
×1
Weapon Sword with Trans-Orange Blade pattern
×1
Technic Axle and Pin Connector Angled #4 - 135°
×1
Brick Curved 3 x 3 with Cutout, Light Bluish Grey Markings, Orange Eyes print
×1
Plate 1 x 6
×1
Brick Special 2 x 6 x 1 1/3 with Axle Holes and 2 x 4 Recessed, Ridges at Underside
×1
Technic Axle 4
×1
Technic Brick 1 x 6 [5 Pin Holes]
×1
Brick Round 2 x 2 with Axle Hole
×1
Technic Axle 7
×1
Wheel Arch, Curved Wedge 4 x 3 with 2 x 2 Opening and 4 Studs
×1
Wedge Sloped 45° 2 x 4 Triple
×1
Slope Inverted 45° 4 x 2 Double with 2 x 2 Recessed
×1
Brick Special 1 x 2 with Studs on 2 Sides
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Plate Special 1 x 2 with Handle on End [Closed Ends]
×1
Plate Special 1 x 2 with Clip Horizontal on End
×1
Bar 6L with Stop Ring
×1
Weapon Lightsaber Hilt with Bottom Ring
×1
Wedge Plate 2 x 4 27° Right
×1
Wedge Plate 2 x 4 27° Left
×1
Tile Special 2 x 3 with 2 Clips without Tab between Clips
×1
Brick Curved, 3 x 1 with 1/3 Inverted Cutout
×1
Plate Special 1 x 4 Rounded with 2 Open Studs
×1
Plate Special 1 x 3 with 2 Clips on Top
×1
Bar 5L with Handle (Friction Ram)
×1
Slope Curved 4 x 2 No Studs
×1
Slope 45° 1 x 1 x 2/3 Quadruple Convex [Pyramid]
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Weapon Lightsaber Hilt with Bottom Ring
×1
Bar 3L
×1