
Kai's Ninja Race Car EVO
미니피규어 (1)
부품 목록 (45)

Hinge Plate 1 x 2 Locking with 1 Finger On Top
×6
Plate Round 1 x 1 with Solid Stud
×6
Wheel Hard Plastic (37mm D. x 22mm), Pin Hole
×4
Technic Pin without Friction Ridges Lengthwise
×4
Plate 1 x 4
×4
Brick Curved 1 x 2 x 1 No Studs
×4
Plate Special 2 x 2 x 2/3 with Two Studs On Side and Two Raised [Solid Anti-stud]
×4
Weapon Sword / Katana / Shamshir with Capped Pommel [Square Guard]
×3
Slope Curved 2 x 1 No Studs [1/2 Bow]
×2
Technic Pin Connector Round 1L [Beam]
×2
Brick Special 1 x 2 x 1 2/3 with 4 Studs on 1 Side
×2
Tile Special 1 x 2 Grille with Bottom Groove
×2
Tile Special 1 x 2 with Handle
×2
Plate Special 2 x 4 with 2 Pin Holes
×2
Bracket 1 x 2 - 1 x 4 [Rounded Corners at Bottom, Square Corners at Top]
×2
Plate 2 x 4
×2
Plate 1 x 2
×2
Plate 4 x 4
×2
Brick Special 1 x 1 x 1 2/3 with Studs on 1 Side
×2
Technic Pin Long without Friction Ridges, with Anti-Roll Notch
×2
Plate Special 1 x 2 [Open O Top Clip]
×2
Technic Pin Connector 3L with 2 Pins and Center Hole [Pin Ridges Across Part]
×2
Plate Special 1 x 1 with Clip Vertical [Thick Open O Clip]
×2
Slope 18° 2 x 1 x 2/3 with 4 Slots / Grate
×2
Technic Pin Connector Round [Slotted]
×2
Technic Axle 1.5 with Perpendicular Axle Connector (Technic Pole Reverser Handle)
×2
Slope Curved 4 x 3 with 3 Layers, 1 x 3 Cutout on Underside
×2
Fin Jagged with Axle Hole
×2
Slope Curved 4 x 1 Double with No Studs
×2
Sticker Sheet for Set 71780-1
×1
Slope Curved 2 x 2 x 2/3
×1
Brick Round 2 x 2, Pin Holes
×1
Windscreen 8 x 4 x 2 Curved with Handle
×1
Vehicle Base 6 x 12 x 3/4 with 4 x 2 Recessed Center with Smooth Underside
×1
Technic Brick 1 x 2 with Axle Hole Type 1 [+ Opening] and Bottom Pin
×1
Steering Stand 1 x 2 with Black Steering Wheel
×1
Wedge Plate 4 x 4 with 2 x 2 Cutout
×1
Technic Axle 3
×1
Wedge 3 x 2 Right
×1
Wedge 3 x 2 Left
×1
Slope Curved 4 x 2 No Studs
×1
Bracket 1 x 2 - 1 x 2 Inverted
×1
Technic Pin Connector Round 1L [Beam]
×1
Technic Pin without Friction Ridges Lengthwise
×1
Plate Round 1 x 1 with Solid Stud
×1