
Jango Fett's Slave I
미니피규어 (2)
부품 목록 (142)

Tile Special 1 x 2 Grille with Bottom Groove
×9
Brick 2 x 2 Corner
×8
Tile Special 1 x 2 Grille with Bottom Groove
×8
Plate 1 x 2
×8
Slope 45° 2 x 1 with Bottom Pin
×8
Brick Curved 8 x 2 x 2
×8
Cone 1 x 1 [No Top Groove]
×8
Hinge Tile 1 x 4
×8
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×7
Plate 1 x 4
×7
Plate 2 x 4
×6
Brick Round Corner 2 x 2 Macaroni with Stud Notch
×6
Brick Special 1 x 2 with Pin
×5
Plate 2 x 6
×5
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×5
Hinge Vehicle Roof Holder 1 x 4
×5
Plate 2 x 2 Corner
×4
Technic Pin with Friction Ridges Lengthwise and Center Slots
×4
Hinge Train Gate 2 x 4
×4
Brick Special 1 x 2 with Grille
×4
Brick 2 x 2
×4
Brick 1 x 2
×4
Brick Arch 1 x 5 x 4 Inverted
×4
Brick 1 x 4
×4
Plate 2 x 3
×4
Plate 4 x 6
×4
Bar 1 x 8 with Brick 1 x 2 Curved Top End (Axle Holder Inside Small End)
×4
Slope 45° 2 x 3
×4
Slope 45° 2 x 2
×4
Brick Round 1 x 1 Open Stud
×4
Tile 1 x 1 with Groove
×4
Technic Axle and Pin Connector Angled #4 - 135°
×4
Slope 33° 3 x 2
×4
Plate 1 x 6
×4
Technic Brick 1 x 2 [1 Pin Hole]
×4
Bracket 2 x 2 - 2 x 2
×4
Brick Special 1 x 1 with Headlight
×4
Hinge Vehicle Roof 4 x 4
×4
Plate 1 x 10
×4
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×3
Plate 2 x 2
×3
Minifig Head [Plain] [Blocked Open Stud]
×3
Slope 75° 2 x 2 x 3 [Hollow Studs]
×3
Hinge Vehicle Roof 4 x 4
×3
Slope Inverted 75° 2 x 1 x 3
×2
Slope Inverted 75° 2 x 1 x 3
×2
Plate Special 2 x 2 with Pin on Bottom, Small Holes in Plate and Rotational Locking Fingers on Underside
×2
Technic Brick 1 x 10 [9 Pin Holes]
×2
Hinge Train Gate 2 x 4
×2
Brick 2 x 3
×2
Brick 2 x 2
×2
Brick 1 x 8
×2
Weapon Gun / Pistol / Revolver Large Barrel, Long Grip
×2
Slope 18° 4 x 2
×2
Hinge Brick 1 x 2 Locking with 1 Finger Vertical End
×2
Hinge Brick 1 x 2 Locking with 2 Fingers Vertical End, 9 Teeth
×2
Slope 45° 2 x 4
×2
Hinge Panel 1 x 4 x 3 2/3 with 6 holes, 2 studs on top, Locking 2 Fingers
×2
Brick Round Corner 2 x 2 Macaroni with Stud Notch
×2
Tile 1 x 2 with Slave I Engine Chevron Print [7153]
×2
Tile 1 x 2 with Stylised Computer Console Print
×2
Technic Brick 1 x 2 with Axle Hole Type 1 [+ Opening] and Bottom Ridges
×2
Technic Axle 5.5 with Stop [Flat Short End]
×2
Large Figure Foot, Wedge 3 x 7 x 3
×2
Slope 33° 3 x 2
×2
Brick Arch 1 x 6
×2
Brick Arch 1 x 6
×2
Plate 1 x 8
×2
Brick 1 x 3
×2
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×2
Slope 65° 2 x 2 x 2 Smooth without Bottom Tube
×2
Technic Axle 6
×2
Plate 2 x 6
×2
Technic Brick 1 x 6 [5 Pin Holes]
×2
Cone 4 x 4 x 2, Axle Hole [Plain]
×2
Tile Round 2 x 2 with Bottom Cross
×2
Brick Special 2 x 2 x 2 with Rotation Joint Socket and Rear Pin Hole
×2
Wedge Curved 8 x 3 x 2 Open Right
×2
Wedge Curved 8 x 3 x 2 Open Left
×2
Plate Special 2 x 2 with Grills
×2
Brick Curved 6 x 1
×2
Brick Curved 6 x 1
×2
Brick Curved 6 x 1 with Control Panel Print
×2
Brick Curved 6 x 1 Inverted
×2
Slope 33° 3 x 1
×2
Slope 33° 3 x 1
×2
Cupboard 2 x 3 x 2 with Solid Studs
×2
Cupboard 2 x 3 x 2 Door
×2
Brick Round 1 x 1 with Fins, Open Stud
×2
Cone 1 x 1 [No Top Groove]
×2
Plate Special 1 x 2 with Bar Up [Horizontal Arm 6mm]
×2
Bar 1 x 3 [Clip / Anti-Stud]
×2
Plate Round Corner 6 x 6
×2
Wedge Plate 6 x 6 Cut Corner
×2
Brick 1 x 10
×2
Magnet Cylindrical
×2
Hose, Ribbed 7mm D. 4L / 3.2cm
×2
Brick 2 x 6
×1
Brick 2 x 6
×1
Magnet Holder 2 x 3
×1
