
Dry Bowser Castle Battle Expansion Set
부품 목록 (467)

Slope 45° 1 x 1 x 2/3 Quadruple Convex [Pyramid]
×30
Brick Round 1 x 1 diameter Tube with 90 Degree Elbow (2 x 2 x 1) and Axle Holes (Crossholes) at each end
×26
Brick 1 x 1
×23
Brick 1 x 2
×20
Brick 2 x 2 Corner
×18
Brick Special 1 x 1 with Headlight
×16
Plate Special 1 x 2 with 1 Stud with Groove and Inside Stud Holder (Jumper)
×15
Technic Pin 1/2 with Friction
×15
Technic Pin Connector Round 1L [Beam]
×14
Technic Axle 2 Notched
×14
Plate 1 x 2
×13
Slope 45° 2 x 1 Inverted with 2/3 Cutout
×12
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×12
Technic Pin Long with Friction Ridges Lengthwise, 1 Center Slot
×11
Tile Round 1 x 1 Quarter
×10
Tile 2 x 2 Curved, Macaroni
×10
Bar 4L (Lightsaber Blade / Wand)
×10
Equipment Candlestick
×10
Brick Curved 1 x 2 x 1 1/3 with Curved Top
×10
Plate Round 1 x 1 with Solid Stud
×10
Tile 2 x 4 with Groove
×10
Tile Round 1 x 1
×10
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×9
Bar 3L
×9
Slope 45° 1 x 1 x 2/3 Quadruple Convex [Pyramid]
×8
Tile Round 1 x 1 Quarter
×8
Technic Brick 1 x 2 [1 Pin Hole]
×8
Plate 1 x 2
×7
Technic Pin without Friction Ridges Lengthwise
×7
Technic Pin with Friction Ridges Lengthwise with No Center Slots
×7
Tile Round 1 x 1
×7
Plate Special Round 2 x 2 with Center Stud (Jumper Plate)
×6
Tile Special 1 x 2 Grille with Bottom Groove
×6
Plate 2 x 2 Corner
×6
Tile Round 1 x 1 Quarter
×6
Tile 2 x 3
×6
Tile 1 x 2 with Groove
×6
Technic Brick 1 x 2 with Axle Hole Type 1 [+ Opening] and Bottom Pin
×6
Wave / Flame Small with Pin
×6
Plate 2 x 6
×6
Hinge Brick 1 x 4 [Upper]
×6
Hinge Brick 1 x 4 [Lower]
×6
Technic Axle 3
×6
Weapon Hilt Symmetric
×6
Plate 1 x 2
×5
Tile 1 x 1 with Groove
×5
Plate Special 1 x 2 Rounded with 2 Open Studs
×5
Brick Arch 1 x 4
×5
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×5
Bracket 1 x 2 - 2 x 2 Inverted
×5
Tile 6 x 6 with Bottom Tubes
×4
Plate Round 6 x 6 with Hole
×4
Wedge Sloped 45° 2 x 2 Corner
×4
Brick Arch 1 x 5 x 4 [Continuous Bow, Raised Underside Cross Supports]
×4
Tile Round 2 x 2 with Bottom Stud Holder
×4
Slope Curved 2 x 2 x 2/3
×4
Plate Special 1 x 2 with Three Teeth [Tri-Tooth]
×4
Plate Special 1 x 2 with 1 Stud with Groove and Inside Stud Holder (Jumper)
×4
Plate Special 1 x 2 with 1 Stud with Groove and Inside Stud Holder (Jumper)
×4
Slope 45° 2 x 1 with 2/3 Cutout [New Version]
×4
Slope 45° 2 x 1 with 2/3 Cutout [New Version]
×4
Support Half Round 2 x 4 x 13
×4
Plate Special 1 x 2 with Pin Hole Underneath
×4
Rock Brick 8 x 8 x 6
×4
Tile 1 x 4 with Groove
×4
Plate 2 x 12
×4
Plate 4 x 4 Corner
×4
Brick Special 1 x 4 with Groove
×4
Wedge Plate 2 x 2 Cut Corner
×4
Tile 2 x 2 Curved, Macaroni
×4
Slope 45° 2 x 1 with 2/3 Inverted Cutout and no stud
×4
Slope 45° 2 x 1 with 2/3 Inverted Cutout and no stud
×4
Brick 2 x 3
×4
Plate 2 x 4
×4
Plate 2 x 2
×4
Plate 2 x 2
×4
Plate 1 x 2
×4
Plate 1 x 1
×4
Plate 1 x 1
×4
Plate 2 x 8
×4
Plate Round Corner 4 x 4
×4
Tile 2 x 2 with Groove
×4
Tile 1 x 2 with Groove
×4
Brick 1 x 2 x 2 with Inside Stud Holder
×4
Brick Special 1 x 1 x 1 2/3 with Studs on 1 Side
×4
Slope Double 45° 1 x 1
×4
Plate Special 1 x 2 Rounded with 2 Open Studs
×4
Plate Special 1 x 2 Rounded with 2 Open Studs
×4
Tile 45° Cut 2 x 2 (Triangle)
×4
Slope Inverted 45° 2 x 1
×4
Plate 1 x 6
×4
Plate 2 x 6
×4
Hinge Brick 1 x 2 Base
×4
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×4
Wheel 11 x 8 with Center Groove
×4
Plate Special 2 x 2 x 2/3 with Two Studs On Side and Two Raised [Half Hollow Anti-stud] - Updated Version
×4
Bracket 1 x 2 - 2 x 2
×4
Plate Special 1 x 2 [Open O Top Clip]
×4
Plate Special 1 x 1 with Tooth
×4
Slope 18° 4 x 1
×4