
Wiggler's Poison Swamp Expansion Set
부품 목록 (136)

Plate 1 x 2
×21
Plate Special 2 x 2 with Only 2 studs
×16
Tile Round 2 x 2 with Bottom Stud Holder
×12
Plate Special 1 x 3 with 2 Studs with Groove and Inside Stud Holder (Jumper)
×12
Bracket 1 x 1 - 1 x 2 Inverted
×10
Bracket 1 x 2 - 2 x 2 Inverted
×10
Plant, Flower, Plate Round 1 x 1 with 5 Petals
×9
Plate Special 3 x 2 with Rounded End, Hole
×8
Brick Curved 1 x 1 x 2/3 Double Curved Top, No Studs
×8
Plate 1 x 2
×7
Tile 1 x 2 with Groove
×7
Plate 2 x 8
×6
Brick Round 2 x 2 with Axle Hole
×6
Hinge Plate 2 x 4 with Pin Hole with 2 Holes - Bottom
×6
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×5
Plate 2 x 4
×5
Plate 4 x 4
×5
Technic Pin without Friction Ridges Lengthwise
×5
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×5
Slope 30° 1 x 2 x 2/3
×5
Slope 45° 2 x 1 with 2/3 Inverted Cutout and no stud
×4
Brick 1 x 2
×4
Plate 2 x 4
×4
Plate 2 x 4
×4
Plate 2 x 3
×4
Plate 2 x 3
×4
Plate 2 x 2
×4
Tile 1 x 8 with Groove
×4
Plate Round Corners 4 x 4 x 2/3 Circle with Reduced Knobs
×4
Feet, 2 x 3 x 2/3 with 6 Studs on Top
×4
Plate Special 1 x 2 with Bar Up [Horizontal Arm 5mm]
×4
Brick Special 1 x 2 with Masonry Brick Profile
×4
Tile Round 2 x 2 with Bottom Stud Holder
×3
Slope Curved 2 x 2 x 2/3
×3
Plate 2 x 3
×3
Plate 2 x 2
×3
Slope 45° 2 x 2
×3
Tile 1 x 2 with Groove
×3
Plant, Plate 1 x 1 Round with 3 Leaves
×3
Tile Round 2 x 4
×3
Plate Round Corners Double 4 x 8 with 2 x 2 Cutout and 2 x 8 Raised Studs, Reduces Nubs
×3
Slope 30° 1 x 2 x 2/3
×3
Tile 2 x 4 with Groove
×3
Plate Special 1 x 2 with Clip Horizontal on Side
×2
Tile Round 2 x 2 with Bottom Stud Holder
×2
Plate Special 1 x 2 with End Towball
×2
Plate 2 x 2 Corner
×2
Tile 1 x 4 with Groove
×2
Plate 2 x 12
×2
Plate Special 1 x 2 Side Handle [Free Ends]
×2
Tile 2 x 3
×2
Brick 1 x 2
×2
Brick 1 x 2 with Star with Eyes Print
×2
Plate 1 x 2
×2
Plate 1 x 2
×2
Plate 1 x 8
×2
Plate Special 1 x 2 Rounded with 2 Open Studs
×2
Plate 1 x 6
×2
Plate 2 x 6
×2
Technic Axle Pin with Friction Ridges Lengthwise
×2
Plate 1 x 10
×2
Bar 1L with Clip [Cut Edges and One Side Hole] [Gap in Clip]
×2
Plate Round 1 x 1 with Solid Stud
×2
Tile 1 x 3
×2
Technic Brick 1 x 1 with Pin Hole
×2
Arm, Long, with Technic Pin
×2
Plate Round Corners 4 x 4 x 2/3 Circle with Reduced Knobs
×2
Brick Special 1 x 2 x 1 2/3 with 8 Studs on 3 Sides
×2
Creature Body Part, Cheep Cheep / Paragoomba Wing
×2
Bracket 1 x 1 - 1 x 2 Inverted
×2
Brick Special 1 x 1 with Stud on 1 Side
×2
Panel 1 x 2 x 3 [Side Supports / Hollow Studs]
×2
Plate Special 2 x 2 with Groove and Center Stud (Jumper)
×2
Tile 8 x 16 with Bottom Tubes
×2
Bracket 1 x 2 - 2 x 2 Inverted
×2
Plant, Leaves 6 x 5 Swordleaf with Clip [Thick Open O Clip]
×1
Brick Special 1 x 2 with 2 Studs on 1 Side
×1
Brick Arch 1 x 5 x 4 [Continuous Bow, Raised Underside Cross Supports]
×1
Plate Special 1 x 2 with 5.9mm Centre Side Towball
×1
Tile Round 2 x 2 with Bottom Stud Holder with Three Dark Tan Lines Print
×1
Slope Curved 2 x 2 x 2/3
×1
Panel 1 x 4 x 1 with Rounded Corners [Thin Wall]
×1
Tile Round 1 x 1 with Hollow Bar
×1
Brick Special 1 x 2 x 1 2/3 with 4 Studs on 1 Side
×1
Brick 2 x 2 Corner
×1
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×1
Brick 2 x 4
×1
Brick 1 x 2 with Oval Eyes Print
×1
Brick 1 x 2 with Green Eyes (Koopa Troopa) Print
×1
Brick 1 x 1
×1
Brick 1 x 4
×1
Plate 2 x 4
×1
Plate 2 x 3
×1
Plate 2 x 2
×1
Plate 2 x 2
×1
Plate 1 x 2
×1
Plate 4 x 6
×1
Tile 2 x 2 with Groove
×1
Tile 2 x 2 with Star and Barcode Print (Sticker)
×1
Tile 2 x 2 with Goomba Face Looking Left Print
×1