
Akida Creature of Water
부품 목록 (51)

Plate Round 1 x 1 with Solid Stud
×24
Technic Bush
×6
Large Figure Wing, Small
×5
Insect Body Part, Leg / Tail / Tentacle / Claw
×4
Arm Mechanical with Clip [Thick Support]
×4
Technic Axle 5 with Stop
×3
Technic Pin with Friction Ridges Lengthwise and Center Slots
×3
Hinge Cylinder 1 x 2 Locking with 1 Finger and Axle Hole On Ends
×3
Hinge Cylinder 1 x 2 Locking with 2 Click Fingers and Axle Hole, 9 Teeth
×3
Cone 1 x 1 [Top Groove]
×3
Propeller 3 Blade 3 Diameter with Axle Cross
×3
Technic Pin Connector Hub with 1 Pin with Friction Ridges Lengthwise
×2
Wave / Flame Rounded Single with Pin
×2
Launcher Trigger, Weapon Rapid Shooter, Flat Axle Hole
×2
Launcher, Weapon Rapid Shooter Six Barrel, 3 Fingers
×2
Technic Axle Pin 3L with Friction Ridges Lengthwise and 2L Axle
×2
Large Figure Accessory, Shadow Trap
×2
Technic Axle and Pin Connector Angled #1
×2
Technic Axle 2 Notched
×2
Technic Axle and Pin Connector Perpendicular 3L with Centre Pin Hole
×2
Technic Beam 3 x 3 L-Shape with Quarter Ellipse Thin
×2
Technic Axle and Pin Connector Perpendicular Double
×2
Technic Beam 1 x 4 Thin
×2
Technic Axle 6
×2
Technic Tooth 1 x 3 with Axle Hole [Rounded Underside]
×2
Technic Beam 1 x 2 Thin
×2
Bar 1L with Clip [Cut Edges and One Side Hole] [Gap in Clip]
×2
Cone 1 x 1 [Top Groove]
×2
Large Figure Skeletal, Limb, 4L with Ball Joint on Axle and Ball Socket
×2
Large Figure Weapon, Barrel with 2 Pin Holes and 3 Axle Holes
×2
Large Figure Mask with Back with Marbled Trans-Dark Blue Pattern
×1
Large Figure Torso, Armor Uniter with 2 Pin Holes on Front, Axle and Pin Holes on Sides
×1
Technic Pin Long with Friction Ridges Lengthwise and Stop Bush [3 Lateral Holes, Big Pin Hole]
×1
Technic Axle 5
×1
Technic Bush 1/2 Smooth with Axle Hole Semi-Reduced
×1
Technic Beam 1 x 5 Thick
×1
Technic Pin without Friction Ridges Lengthwise
×1
Technic Axle 4
×1
Technic Axle 8
×1
Brick Round 2 x 2 with Axle Hole
×1
Technic Pin 1/2
×1
Dish 6 x 6 Inverted (Radar) with Solid Studs
×1
Technic Axle 3
×1
Technic Ball Joint with Through Axle Hole
×1
Light Cover 1 x 1 Round with Internal Bar / Bionicle Barraki Eye
×1
Technic Axle 5.5 with Stop [Rounded Short End]
×1
Technic Beam 1 x 2 Thick with Pin Hole and Axle Hole
×1
Technic Axle and Pin Connector Perpendicular
×1
Technic Axle 1.5 with Perpendicular Axle Connector (Technic Pole Reverser Handle)
×1
Animal Body Part, Barb / Claw / Tooth / Talon / Horn, Medium
×1
Large Figure Skeletal, Limb with Ball Joint on Axle and Ball Socket and Four Holes
×1