
Emmet's Construct-o-Mech
미니피규어 (3)

Skeleton, Robot (Robo-Skeleton)
fig-007020×2

Emmet, Happy / Questioning
fig-001449×1

Unikitty, Angry Kitty
fig-007039×1
부품 목록 (186)

Plate Special 1 x 2 with Door Rail
×2
Technic Axle and Pin Connector Angled #4 - 135°
×2
Technic Beam 1 x 5 Thick
×2
Plate 1 x 8
×2
Hinge Brick 1 x 2 Base
×2
Brick Round 2 x 2 with Axle Hole
×2
Dish 4 x 4 Inverted [Radar]
×2
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×2
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×2
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×2
Plate Special 1 x 1 with Clip Light, Bar Hole [Thick Ring]
×2
Tile Round 2 x 2 with Bottom Cross
×2
Brick Curved 6 x 1
×2
Slope Inverted 34° 3 x 1 with Internal Stopper
×2
Technic Axle Pin with Friction Ridges Lengthwise
×2
Technic Rotation Joint Disk with Pin Hole and 3L Beam Thick
×2
Technic Rotation Joint Disk with Pin and 3L Beam Thick
×2
Cone 4 x 4 x 2 Hollow No Studs
×2
Technic Rotation Joint Ball Loop with Two Perpendicular Pins with Friction
×2
Wedge Curved 2 x 3 x 2/3 Two Studs, Wing End
×2
Technic Brick Special 2 x 2 with Pin Hole, Rotation Joint Socket
×2
Technic Brick Special 2 x 2 with Pin Hole, Rotation Joint Ball Half [Vertical Side]
×2
Wheel Arch, Mudguard 4 x 2 1/2 x 2 with 2 x 2 Plate
×2
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×2
Brick 1 x 12
×2
Hinge Brick 2 x 2 Top Plate Thin
×2
Brick Special 2 x 2 with Pin and Axle Hole
×2
Technic Pin Connector Round [Slotted]
×2
Plate Special 1 x 2 with Clip Horizontal on End
×2
Bar 6L with Stop Ring
×2
Technic Axle 1.5 with Perpendicular Axle Connector (Technic Pole Reverser Handle)
×2
Plate Special 2 x 2 with Bar Frame Octagonal, Reinforced, Completely Round Studs
×2
Slope 30° 1 x 2 x 2/3
×2
Plate Special 2 x 2 with Groove and Center Stud (Jumper)
×2
Cylinder 1 x 5 1/2 with Handle (Friction Cylinder)
×2
Bar 5L with Handle (Friction Ram)
×2
Plate Special 1 x 2 with Bar Up [Horizontal Arm 5mm]
×2
Slope Brick Curved 2 x 4 x 2/3 No Studs, with Bottom Tubes
×2
Chain 6L [5 Links]
×2
Bracket 1 x 2 - 2 x 4
×2
Weapon Sword / Foil / Épée
×2
Support 2 x 2 x 10 Girder Triangular Vertical - Type 4 - 3 Posts, 3 Sections
×2
Arm Mechanical with Clip [Thick Support]
×2
Technic Beam Triangle Thin [Type II]
×2
Sticker Sheet for Set 70814-1
×1
Wedge Plate 3 x 6 Cut Corners
×1
Tile 1 x 4 with SM-xxxxxxxx Print - Set 70814
×1
Plate Special 1 x 2 Side Handle [Free Ends]
×1
Brick 2 x 4
×1
Plate 4 x 6
×1
Plate 6 x 8
×1
Technic Brick 1 x 2 [2 Pin Holes]
×1
Technic Axle Connector with Axle Hole
×1
Technic Gear 12 Tooth Double Bevel
×1
Technic Beam 1 x 5 Thick
×1
Plate 1 x 6
×1
Technic Bush
×1
Technic Axle Pin without Friction Ridges Lengthwise
×1
Plate Special 1 x 4 Offset with Bar Holes
×1
Brick Curved 2 x 2 x 2/3 Two Studs and Curved Slope End
×1
Plate Special 1 x 2 [Side Handle Closed Ends]
×1
Technic Rubber Belt Medium [26mm ID] [Round Cross Section]
×1
Slope Curved 4 x 1 Double with No Studs
×1
Brick and Axle Separator v2.0
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×3
Plate Round 1 x 1 with Solid Stud
×3
Technic Pin 1/2
×2
Plate Round 1 x 1 with Solid Stud
×2
Tile Round 1 x 1
×2
Tile Special 1 x 2 Grille with Bottom Groove
×1
Technic Pin with Friction Ridges Lengthwise and Center Slots
×1
Lever Small Base with Black Lever
×1
Plate 1 x 1
×1
Plate 1 x 1
×1
Tile 1 x 1 with Groove
×1
Tile 1 x 1 with Groove
×1
Tile 1 x 1 with White and Red Gauge Print
×1
Technic Bush
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Arm Mechanical Straight (Droid) [2 Clips at 90°]
×1
Plate Round 1 x 1 with Solid Stud
×1
Leg Skeleton
×1
Plate Round 1 x 1 with Open Stud
×1
Creature Body Part, Horn (Unicorn)
×1
Weapon Sword / Foil / Épée
×1