
Strainor's Saber Cycle
미니피규어 (2)
부품 목록 (91)

Slope 45° 2 x 1 with 2/3 Cutout [New Version]
×6
Plate Special 1 x 1 with Clip Horizontal [Thick Open O Clip]
×5
Technic Pin 1/2
×4
Bracket 1 x 2 - 2 x 2
×4
Plate Special 1 x 1 with Tooth
×4
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×4
Plate Round 1 x 1 with Solid Stud
×4
Technic Beam 1 x 3 Thin
×4
Plate Special 1 x 2 [Top Clip]
×4
Tool Saw with Handle and Tooth
×3
Brick Special 1 x 2 with Masonry Brick Profile
×3
Bracket 1 x 2 - 1 x 4 [Rounded Corners]
×2
Animal Body Part, Barb / Claw / Tooth / Talon / Horn, Large
×2
Slope Curved 4 x 1 No Studs [Stud Holder with Symmetric Ridges]
×2
Plate Special 1 x 2 with Pin Hole on Top
×2
Slope Curved 2 x 1 No Studs [1/2 Bow]
×2
Insect Body Part, Leg / Tail / Claw / Rib with Axle
×2
Bar 4L with Flame Protrusions and Marbled Trans-Yellow Pattern
×2
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×2
Plate 2 x 2
×2
Plate 1 x 2
×2
Slope 45° 2 x 1 with Bottom Pin
×2
Technic Axle and Pin Connector Angled #6 - 90°
×2
Technic Beam 1 x 9 Bent (7 - 3) Thick
×2
Plate Special 1 x 1 with Clip Light, Bar Hole [Thick Ring]
×2
Propeller 8 Blade 5 Diameter
×2
Technic Beam 1 x 2 Thin
×2
Wheel 11 x 8 with Center Groove
×2
Slope 33° 3 x 1
×2
Wedge Plate 3 x 2 Right
×2
Wedge Plate 3 x 2 Left
×2
Technic Axle 3
×2
Wedge Curved 2 x 3 x 2/3 Two Studs, Wing End
×2
Cone 1 x 1 [Top Groove]
×2
Plate Special 1 x 2 with Handle on End [Closed Ends]
×2
Plate Special 1 x 1 with Clip Vertical [Thick Open O Clip]
×2
Wave / Flame Rounded with Base Pegs
×2
Slope 18° 2 x 1 x 2/3 with 4 Slots / Grate
×2
Plate Round 1 x 1 with Solid Stud
×2
Slope 30° 1 x 2 x 2/3
×2
Brick Special 1 x 2 with Masonry Brick Profile
×2
Bracket 1 x 2 - 2 x 2 Inverted
×2
Bar Holder with Clip
×1
Rock 1 x 1 Crystal 4 Point
×1
Technic Axle Pin 3L with Friction Ridges Lengthwise and 1L Axle
×1
Wedge Sloped 45° 2 x 2 Corner
×1
Slope Curved 2 x 2 x 2/3
×1
Plate Special 1 x 2 with Three Teeth [Tri-Tooth]
×1
Technic Pin Connector Round 1L [Beam]
×1
Sticker Sheet for Set 70220-1
×1
Tile Special 1 x 2 with Handle
×1
Handlebars
×1
Rock 1 x 1 Jewel / Gem 24 Facet
×1
Plate 2 x 4
×1
Plate 2 x 3
×1
Plate 1 x 2
×1
Bar 4L (Lightsaber Blade / Wand)
×1
Technic Brick 1 x 2 [2 Pin Holes]
×1
Technic Axle Connector with Axle Hole
×1
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×1
Technic Axle 8
×1
Technic Bush
×1
Plate 2 x 10
×1
Brick Round 2 x 2 with Axle Hole
×1
Technic Axle Pin with Friction Ridges Lengthwise
×1
Technic Beam 1 x 2 Thick
×1
Technic Axle 7
×1
Technic Pin Connector Perpendicular 2 x 2 Bent
×1
Plate Special 1 x 2 [Side Handle Closed Ends]
×1
Bar 1L with Clip [Cut Edges and One Side Hole] [Gap in Clip]
×1
Wedge Plate 2 x 4
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Tyre 43.2 x 14 Offset Tread
×1
Wheel 30 x 14
×1
Slope 65° 2 x 1 x 2
×1
Technic Pin 1/2 with 2L Bar Extension
×1
Weapon Lightsaber Hilt with Bottom Ring
×1
Technic Pin Long with Friction Ridges Lengthwise, 2 Center Slots
×1
Technic Axle and Pin Connector Perpendicular Double 4L
×1
Bracket 1 x 2 - 1 x 2
×1
Bracket 1 x 2 - 1 x 2
×1
Technic Pin Connector Round 1L [Beam]
×1
Technic Bush
×1
Technic Pin 1/2
×1
Bar 1L with Clip [Cut Edges and One Side Hole] [Gap in Clip]
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Plate Round 1 x 1 with Solid Stud
×1
Plate Round 1 x 1 with Solid Stud
×1
Weapon Lightsaber Hilt with Bottom Ring
×1
Tile Round 1 x 1
×1
