
Braptor's Wing Striker
미니피규어 (2)
부품 목록 (74)

Plate Round 1 x 1 with Solid Stud
×9
Plate Special 3 x 2 with Rounded End, Hole
×8
Tile Special 1 x 2 Grille with Bottom Groove
×6
Plate 2 x 3
×5
Slope Curved 3 x 1 No Studs
×4
Creature Body Part, Dragon Wing 8 x 10 [Plain]
×4
Technic Pin with Friction Ridges Lengthwise and Towball
×4
Plate 1 x 2
×3
Plate 1 x 4
×3
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×3
Equipment Telescope / Torch / Spyglass, Support Round 1 x 1 x 1 2/3
×3
Tile 1 x 6 with Groove
×3
Plate Special 1 x 2 [Top Clip]
×3
Animal Body Part, Barb / Claw / Tooth / Talon / Horn, Large
×2
Plate 3 x 3
×2
Slope Curved 2 x 2 x 2/3
×2
Plant, Grass Stem with Bar Hole [3.2mm]
×2
Brick Special 1 x 4 with Groove
×2
Plate 4 x 4
×2
Slope 45° 2 x 1 with Bottom Pin
×2
Technic Link 1 x 6 without Stoppers
×2
Technic Axle and Pin Connector Angled #6 - 90°
×2
Technic Pin without Friction Ridges Lengthwise
×2
Plate Special 1 x 2 with 1 Stud with Groove (Jumper)
×2
Plate Special 1 x 8 with Door Rail
×2
Weapon Lightsaber Hilt with Bottom Ring
×2
Slope Curved 4 x 1 Double with No Studs
×2
Plate Special 2 x 2 x 2/3 with Two Studs On Side and Two Raised [Solid Anti-stud]
×2
Bar Holder with Clip
×1
Rock 1 x 1 Crystal 4 Point
×1
Tile Special 2 x 2 Inverted
×1
Slope Curved 2 x 1 No Studs [1/2 Bow]
×1
Weapon Gun / Blaster 1 x 2 x 2/3 with Studs on Sides and Handle
×1
Sticker Sheet for Set 70128-1
×1
Wedge Plate 3 x 6 Cut Corners
×1
Plate 2 x 2 Corner
×1
Plant, Leaves 4 x 3
×1
Plate 2 x 12
×1
Brick 1 x 2
×1
Plate 2 x 2
×1
Plate 4 x 4
×1
Hinge Brick 1 x 2 Locking with 2 Fingers Vertical End, 9 Teeth
×1
Bar 4L (Lightsaber Blade / Wand)
×1
Plate Special 1 x 2 with Door Rail
×1
Wedge Plate 4 x 6 Cut Corners
×1
Hinge Brick 1 x 2 Base
×1
Mudguard 2 x 4 with 2 x 2 Studs and Flared Wings
×1
Wedge Curved 6 x 4 Triple
×1
Wedge Curved Inverted 6 x 4
×1
Wedge Plate 3 x 2 Right
×1
Wedge Plate 3 x 2 Left
×1
Hinge Plate 1 x 2 Locking with 1 Finger on Side, with Groove
×1
Brick Special 1 x 2 x 2/3 with Studs on Sides
×1
Dish 2 x 2 Inverted [Radar]
×1
Bar 1L with Clip [Cut Edges and One Side Hole] [Gap in Clip]
×1
Brick Special 1 x 2 with Studs on 2 Sides
×1
Weapon Axe Head, Clip-on (Viking) [Thick Clip]
×1
Cone 1 x 1 [Top Groove]
×1
Plate Special 1 x 2 with Handle on End [Closed Ends]
×1
Hinge Brick 2 x 2 Top Plate Thin
×1
Tile 2 x 4 with Groove
×1
Plate Special 2 x 2 with Groove and Center Stud (Jumper)
×1
Plate Special 1 x 2 with Bar Up [Horizontal Arm 5mm]
×1
Slope Curved 4 x 2 No Studs
×1
Tile Round 1 x 1
×1
Weapon Sai
×1
Plate Round 1 x 1 with Solid Stud
×2
Technic Pin without Friction Ridges Lengthwise
×1
Bar 1L with Clip [Cut Edges and One Side Hole] [Gap in Clip]
×1
Weapon Axe Head, Clip-on (Viking) [Thick Clip]
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Weapon Lightsaber Hilt with Bottom Ring
×1
Tile Round 1 x 1
×1
Weapon Sai
×1
