
Equila's Ultra Striker
미니피규어 (3)
부품 목록 (127)

Technic Pin 1/2
×14
Plate 2 x 4
×12
Technic Axle 2 Notched
×10
Slope 30° 1 x 2 x 2/3
×8
Tile Special 1 x 2 Grille with Bottom Groove
×6
Plate 1 x 1
×6
Technic Bush 1/2 Smooth with Axle Hole Semi-Reduced
×6
Technic Pin Long with Friction Ridges Lengthwise, 2 Center Slots
×6
Animal Body Part, Barb / Claw / Tooth / Talon / Horn, Medium
×6
Slope 45° 2 x 1 with 2/3 Cutout [Original Version]
×6
Plate 2 x 2
×5
Plate 1 x 2
×5
Wheel 30.4 x 20 without Pinholes, with Reinforced Rim
×5
Creature Body Part, Wing 9L with Stylized Feathers
×4
Plate Special 2 x 2 with 1 Pin Hole [Split Underside Ribs]
×4
Brick 2 x 4
×4
Plate 1 x 2
×4
Slope 45° 2 x 2
×4
Technic Axle and Pin Connector Angled #1
×4
Plate 1 x 6
×4
Technic Brick 1 x 16 [15 Pin Holes]
×4
Hinge Plate 1 x 2 Locking with 2 Fingers On End, with Groove, 9 Teeth
×4
Technic Axle Connector Smooth [with x Hole + Orientation]
×4
Slope 65° 2 x 1 x 2
×4
Plate Special 1 x 2 with Clip Horizontal on End
×4
Technic Axle and Pin Connector Perpendicular
×4
Tile 2 x 4 with Groove
×4
Technic Axle 4 with Stop
×4
Plate Special 1 x 2 [Top Clip]
×4
Tile 2 x 2 with Groove
×3
Technic Ball Joint
×3
Technic Bush
×3
Plate 2 x 6
×3
Creature Body Part, Wing 9L with Stylized Feathers
×2
Rock 1 x 1 Crystal 4 Point
×2
Slope Curved 4 x 1 No Studs [Stud Holder with Symmetric Ridges]
×2
Brick Special 1 x 2 with 2 Studs on 1 Side
×2
Brick Curved 10 x 1 [Symmetric Inside Ridges]
×2
Panel 1 x 4 x 1 with Rounded Corners [Thin Wall]
×2
Brick 2 x 2 Corner
×2
Tile 1 x 4 with Groove
×2
Tile 1 x 4 with Groove
×2
Technic Pin with Friction Ridges Lengthwise and Center Slots
×2
Plate Special 2 x 2 with 2 Pin Holes
×2
Brick 2 x 3
×2
Brick 2 x 2
×2
Brick 1 x 1
×2
Plate 2 x 4
×2
Plate 2 x 3
×2
Slope 18° 4 x 2
×2
Hinge Brick 1 x 2 Locking with 2 Fingers Vertical End, 9 Teeth
×2
Slope 45° 2 x 2
×2
Slope 45° 2 x 1 with Bottom Pin
×2
Wedge Plate 4 x 4 Cut Corner
×2
Hinge Cylinder 1 x 2 Locking with 1 Finger and Axle Hole On Ends
×2
Plate Round Corner 4 x 4
×2
Technic Axle and Pin Connector Angled #5 - 112.5°
×2
Technic Axle Connector with Axle Hole
×2
Technic Brick 1 x 2 with Axle Hole Type 2 [X Opening]
×2
Technic Beam 1 x 3 Thick
×2
Brick 1 x 3
×2
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×2
Plate 1 x 6
×2
Technic Brick 1 x 2 [1 Pin Hole]
×2
Technic Brick 1 x 2 [1 Pin Hole]
×2
Technic Brick 1 x 8 [7 Pin Holes]
×2
Plate 1 x 4
×2
Wedge Plate 4 x 2 Right
×2
Wedge Plate 4 x 2 Left
×2
Hinge Tile 1 x 3 Locking with 1 Finger on Top
×2
Hinge Plate 1 x 2 Locking with 1 Finger On End, with Groove
×2
Bracket 1 x 2 - 2 x 2
×2
Technic Axle 3
×2
Wedge Plate 12 x 3 Left
×2
Wedge Plate 12 x 3 Right
×2
Weapon Axe Head, Clip-on (Viking) [Thin Clip]
×2
Arm Mechanical with Clip [Thin Support]
×2
Technic Tread Large [36 Links]
×2
Projectile, Technic Competition Arrow, Liftarm Shaft with Hollow Black Rubber End
×2
Flexible Ribbed Hose 8mm Ends 19L with Blue Centre Pattern
×2
Launcher, Technic Competition Cannon Flat Bottom [Complete Assembly]
×2
Plate 1 x 12
×2
Brick 1 x 12
×2
Brick Arch 1 x 4 x 2
×2
Brick Curved 1 x 4 x 1 1/3 No Studs, Lowered Inside Support
×2
Brick Special 1 x 1 with Stud on 1 Side
×2
Plate Special 1 x 2 with Bar Up [Horizontal Arm 5mm]
×2
Wedge Plate 3 x 4 with Stud Notches [Reinforced Underside]
×2
Plate Special 4 x 6 with Trap Door Hinge [Long Pins]
×2
Bracket 1 x 2 - 2 x 2 Inverted
×2
Weapon Sword Double Blade with Bar Holder [Chi Sword]
×1
Sticker Sheet for Set 70013-1
×1
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×1
Brick 2 x 3
×1
Plate 2 x 3
×1
Plate 1 x 2
×1
Plate 2 x 8
×1
Bar 4L (Lightsaber Blade / Wand)
×1
Slope 45° 2 x 1 Triple with Ovoid Bottom Pin
×1
Slope 45° 2 x 1 Double / Inverted with Bottom Stud Holder
×1

