
Galactic Mediator
미니피규어 (3)
부품 목록 (128)

Plate 1 x 2
×20
Engine, Strakes, 2 x 2 Thin Top Plate
×18
Brick 1 x 2
×12
Brick Special 1 x 1 with Headlight
×10
Brick Special 1 x 1 with Headlight
×10
Plate 1 x 4
×9
Brick 2 x 2 Corner
×8
Tile Special 1 x 2 Grille with Bottom Groove
×8
Tyre 15 x 6 Offset Tread Small
×8
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×8
Slope 33° 3 x 1
×8
Wheel 8 x 6
×8
Plate 2 x 2 Corner
×6
Slope 45° 2 x 1 Triple with Ovoid Bottom Pin
×5
Panel 1 x 4 x 3 [Solid Studs]
×5
Hinge Vehicle Roof Holder 1 x 4
×5
Brick 2 x 2 Corner
×4
Tile Special 1 x 2 Grille with Bottom Groove
×4
Wedge Sloped 3 x 3 x 2 Facet Top
×4
Panel 3 x 2 x 6
×4
Brick 2 x 2
×4
Brick 1 x 2
×4
Brick 1 x 1
×4
Brick 1 x 4 with Bottom Tubes, Lowered Center Cross Support
×4
Slope 33° 3 x 2 with SPACE POLICE' print
×4
Plate 1 x 8
×4
Brick Arch 1 x 4
×4
Plate 1 x 6
×4
Technic Brick 1 x 2 [1 Pin Hole]
×4
Plate 1 x 4
×4
Plate Special 1 x 1 with Clip Vertical [Thick U Clip]
×4
Panel 1 x 4 x 3 [Solid Studs]
×4
Plate Special 2 x 2 with Wheel Holders
×4
Panel 1 x 2 x 2 [Solid Studs]
×4
Hinge Plate 1 x 2 with 3 Fingers On Side
×3
Brick 1 x 6 with Bottom Tubes and 2 Lowered Cross Supports
×3
Brick 1 x 4 with Bottom Tubes, Lowered Center Cross Support
×3
Plate 2 x 4
×3
Plate 6 x 6
×3
Hinge Plate 1 x 2 with 2 Fingers and Hollow Studs
×3
Brick Round 2 x 2 x 2 with Axle Hole and Fins
×3
Wing, Tail 4 x 1 x 3
×2
Wedge Plate 10 x 10 with 4x4 Cutout and Cut Corner
×2
Wedge Plate 10 x 10 with 4x4 Cutout and Cut Corner
×2
Wedge Plate 3 x 6 Cut Corners
×2
Tile Special 1 x 2 with Handle
×2
Hinge Bar with 3 Fingers and End Stud (Control Lever)
×2
Brick Special 2 x 4 x 2 with Studs on Sides
×2
Plate 2 x 12
×2
Wedge Plate 3 x 3 Cut Corner
×2
Brick Special 1 x 2 with Pin
×2
Windscreen 4 x 4 x 4 1/3 Helicopter with Space Police II Print
×2
Windscreen 10 x 4 x 2 1/3 Canopy
×2
Antenna 8H Whip
×2
Brick 1 x 2
×2
Brick 1 x 8 with Bottom Tubes and 3 Lowered Cross Supports
×2
Brick 1 x 8 with Bottom Tubes and 3 Lowered Cross Supports
×2
Brick 1 x 6
×2
Plate 2 x 3
×2
Plate 2 x 2
×2
Plate 1 x 2
×2
Plate 1 x 2
×2
Plate 1 x 1
×2
Plate 1 x 1
×2
Plate 4 x 6
×2
Slope 45° 2 x 2
×2
Slope 45° 2 x 2 with Horizon Indicator Screen Print
×2
Tile 1 x 2 with Groove
×2
Tile 1 x 2 with Arrow Short Red with Silver Border Print
×2
Slope 33° 3 x 2
×2
Engine - Smooth, Small 1 x 2 Side Plate [With Axle Holders]
×2
Tail 4 x 2 x 2
×2
Brick 1 x 3
×2
Brick 1 x 3
×2
Plate 1 x 3
×2
Plate 1 x 3
×2
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×2
Hinge Brick 1 x 4 [Upper]
×2
Hinge Brick 1 x 4 [Lower]
×2
Wedge Plate 8 x 4 Wing Left
×2
Wedge Plate 8 x 4 Wing Left
×2
Wedge Plate 8 x 4 Wing Right with Stud Notch
×2
Wedge Plate 8 x 4 Wing Right with Stud Notch
×2
Wedge Plate 4 x 4 Wing Right
×2
Wedge Plate 4 x 4 Wing Left
×2
Antenna 1 x 4 with Rounded Top
×2
Plate Special 1 x 1 with Clip Light, Bar Hole [Thick Ring]
×2
Plate Special 8 x 8 with Grille [No Hole in Center]
×2
Hinge Vehicle Roof 4 x 4
×2
Slope Inverted 34° 3 x 1 without Internal Stopper
×2
Support 2 x 4 x 5 Stanchion Inclined [5mm wide posts]
×2
Plate 1 x 10
×2
Hinge Tile 1 x 2 1/2 with 2 Fingers on Top
×2
Brick Special 1 x 2 x 2/3 with Studs on Sides
×2
Hinge Tile 1 x 4
×2
Brick Special 2 x 2 with Pin and No Axle Hole
×2
Panel 1 x 2 x 2 [Solid Studs]
×2
Plate Special 1 x 1 with Clip Horizontal [Thick U Clip]
×2
Brick 2 x 4 x 2 with Holes on Sides, Reinforced Supports between Tubes
×2
Brick 2 x 4 x 2 with Holes on Sides, Reinforced Supports between Tubes
×2

