Arachnoid Star Base
미니피규어 (3)
Insectoids Droid / Gigabot
fig-000470×2
Danny Longlegs / Corporal Steel with Airtanks
fig-006970×1
Professor Webb / Locust with Shoulder Armor
fig-006971×1
부품 목록 (133)
Plate Round 1 x 1 with Solid Stud
×17
Plate 1 x 4
×14
Plate 1 x 2
×13
Plate 2 x 2
×11
Hinge Plate 1 x 4 Swivel Top / Base - Solid Clip [Complete Assembly]
×10
Brick 1 x 2
×9
Brick 1 x 4
×8
Slope 45° 2 x 1 with Bottom Pin
×8
Plate 1 x 8
×8
Cone 1 x 1 [No Top Groove]
×8
Plate Round 1 x 1 with Solid Stud
×8
Hinge Plate 1 x 2 with 2 Fingers and Hollow Studs
×7
Tile Special 1 x 2 Grille with Bottom Groove
×6
Support Leg Large [Insectoids]
×6
Cone 1 x 1 [No Top Groove]
×6
Plate 2 x 4
×5
Brick Round 2 x 2 with Axle Hole
×5
Support 2 x 4 x 5 Stanchion Inclined [5mm wide posts]
×5
Dish 2 x 2 with Angled Bar
×5
Plate 2 x 2 Corner
×4
Tile 1 x 4 with Groove
×4
Brick 2 x 6
×4
Plate Special 1 x 2 Side Handle [Free Ends]
×4
Wheel Hard Plastic Medium (35mm D. x 31mm)
×4
Brick Special 1 x 4 with Groove
×4
Brick Special 1 x 2 with Grille
×4
Brick 2 x 2
×4
Brick 2 x 2
×4
Brick 1 x 8
×4
Rock 2 x 2 Crystal 3 Point
×4
Plate 2 x 2
×4
Plate 1 x 2
×4
Plate 1 x 2
×4
Slope 45° 2 x 2
×4
Tile 2 x 2 with Insectoid Logo in Triangle Print
×4
Brick 1 x 3
×4
Plate 1 x 6
×4
Plate 6 x 6
×4
Brick Special 1 x 1 with Headlight
×4
Tile Round 2 x 2 with Bottom Cross
×4
Hinge Plate 1 x 2 with 3 Fingers [Hollow Studs]
×4
Slope 33° 3 x 1
×4
Plate Special 1 x 4 Offset with Bar Holes
×4
Slope 53° 3 x 1 x 3 1/3 with Studs on Slope
×4
Brick Special 2 x 4 with Pins
×4
Sticker Sheet for Sets 2964-1, 2965-1, 5316-1, 6817-1, 6837-1, 6903-1, 6905-1, 6907-1, 6909-1, 6919-1, 6969-1, 6977-1
×4
Brick Special 1 x 2 with Pin
×3
Antenna 8H Whip
×3
Magnet Holder 2 x 3
×3
Brick 1 x 2
×3
Dome Hemisphere 4 x 4 Multifaceted
×3
Plate Special 1 x 2 with 4 x 4 disk at 90 degrees
×3
Plate 2 x 3
×3
Slope 45° 2 x 1 with Bottom pin, with Black Crosshairs and Green Insectoid Print
×3
Tile 1 x 2 with Groove
×3
Plate 1 x 3
×3
Plate 1 x 4
×3
Plate Special 1 x 1 with Clip Horizontal [Thick U Clip]
×3
Magnet Cylindrical
×3
Brick 2 x 2 Corner
×2
Wedge Plate 3 x 6 Cut Corners
×2
Plate 2 x 2 Corner
×2
Hinge Bar with 3 Fingers and End Stud (Control Lever)
×2
Bracket 1 x 2 - 1 x 4 [Square Corners]
×2
Plate Special 2 x 2 with 1 Pin Hole [Split Underside Ribs]
×2
Plate Special 2 x 2 with Pin on Bottom
×2
Bar, 4 Top Bars, Palm Tree Top
×2
Brick 1 x 1
×2
Brick 2 x 8
×2
Plate 2 x 4
×2
Cockpit 6 x 6 x 3 1/3 Octagonal Canopy Base
×2
Panel 10 x 10 x 2 2/3 Quarter Saucer Base
×2
Support Leg Small [Insectoids]
×2
Plate 2 x 2
×2
Plate 1 x 2
×2
Plate 6 x 16
×2
Plate 4 x 10
×2
Slope 45° 2 x 2
×2
Tile 1 x 2 with Mars Orbit Display Print
×2
Hinge Plate 2 x 5 with Large Hole [Complete Assembly]
×2
Turntable 4 x 4 Square Base with Top, Complete Assembly
×2
Engine - Smooth, Small 1 x 2 Side Plate [With Axle Holders]
×2
Slope Inverted 45° 2 x 1
×2
Plate 1 x 6
×2
Technic Pin without Friction Ridges Lengthwise
×2
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×2
Plate 2 x 6
×2
Plate Special 1 x 2 with Handles [Flat Ends / Low Attachment]
×2
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×2
Plate 2 x 16
×2
Slope 33° 3 x 1
×2
Slope Inverted 34° 3 x 1 without Internal Stopper
×2
Equipment Weapon, Loudhailer / Speaker / Blaster / Space Gun
×2
Plate Special 1 x 8 with Door Rail
×2
Bracket 3 x 2 - 2 x 2 [aka Space Seat]
×2
Hinge Tile 1 x 4
×2
Arm Piece with Pin, 2 Fingers
×2
Wheel Hard Plastic Small (22mm D. x 24mm)
×2
Technic Brick 1 x 1 with Pin Hole
×2
Windscreen 6 x 6 Octagonal Canopy with Axle hole
×1