
Lunar Launch Site
미니피규어 (3)
부품 목록 (113)

Brick 1 x 2
×13
Cone 1 x 1 [No Top Groove]
×11
Tile 1 x 4 with Groove
×10
Plate 1 x 2
×10
Lever Small Base with Black Lever
×6
Plate 2 x 2
×6
Tyre 15 x 6 Offset Tread Small
×6
Wheel 8 x 6
×6
Dish 2 x 2 Inverted [Radar]
×6
Tile Special 1 x 2 Grille with Bottom Groove
×5
Brick 2 x 2
×5
Plate 2 x 3
×5
Tile 1 x 2 with Groove
×5
Tile 1 x 2 with Blue Screen, Red and Silver Panel Print
×5
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×5
Plate 2 x 4
×4
Tile 1 x 2 with Groove
×4
Plate 1 x 6
×4
Plate 1 x 4
×4
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×4
Plate Special 1 x 1 with Clip Vertical [Thick U Clip]
×4
Plate Special 1 x 2 with Long Stud Receptacle (Space Wing)
×4
Antenna 8H Whip
×3
Brick 1 x 6
×3
Plate 2 x 2
×3
Plate 1 x 2
×3
Tile 1 x 8 with Groove
×3
Plate Special 2 x 2 with Wheel Holders
×3
Hinge Plate 1 x 4 Swivel Top / Base - Solid Clip [Complete Assembly]
×3
Tile Special 1 x 2 Grille with Bottom Groove
×2
Tile 1 x 4 with Groove
×2
Slope Inverted 75° 2 x 1 x 3
×2
Brick 1 x 1 x 5 with Blocked Open or Hollow Stud
×2
Brick 1 x 2 x 5 with Blocked Open Studs and Bottom Stud Holder with Asymmetric Ridges
×2
Brick 1 x 8
×2
Brick 1 x 6
×2
Plate 1 x 1
×2
Plate 4 x 12
×2
Slope 45° 2 x 2
×2
Tile 1 x 2 with Arrow Short Yellow without Black Border Print
×2
Tile 1 x 2 with Arrow Long Yellow with Black Border Print
×2
Tile 1 x 1 with Groove
×2
Plate Special 3 x 2 with Rounded End, Hole
×2
Engine - Smooth, Small 1 x 2 Side Plate [With Axle Holders]
×2
Slope 75° 2 x 2 x 3 [Hollow Studs]
×2
Technic Brick 1 x 2 [1 Pin Hole]
×2
Technic Axle 8
×2
Plate 1 x 4
×2
Plate 2 x 6
×2
Plate 2 x 10
×2
Plate Special 1 x 2 with Handles [Flat Ends / Low Attachment]
×2
Wedge Plate 4 x 4 Wing Right
×2
Wedge Plate 4 x 4 Wing Left
×2
Support Round 2 x 2 x 2 Stand with Reach-Through Center Hole
×2
Plate Special 1 x 1 with Clip Light, Bar Hole [Thick Ring]
×2
Hinge Plate 1 x 2 with 2 Fingers and Hollow Studs
×2
Dish 6 x 6 Inverted, Radar / Webbed [Anti-studs at 90°]
×2
Plate 1 x 10
×2
Brick Special 1 x 2 x 2/3 with Studs on Sides
×2
Brick Special 2 x 2 with Pin and No Axle Hole
×2
Rock Panel Rectangular 4 x 10 x 6 (aka BURP)
×2
Rock Panel Triangular 3 x 8 x 7 (aka LURP)
×2
Bar 1 x 6 [Closed Studs]
×2
Plate Round 1 x 1 with Solid Stud
×2Sticker Sheet for Set 6959-1
×1
Brick 2 x 2 Corner
×1
Wedge Plate 10 x 10 with 4x4 Cutout and Cut Corner
×1
Panel 10 x 10 x 12 Quarter Dome
×1
Windscreen 6 x 6 Octagonal Canopy with Axle hole
×1
Plate 2 x 2 Corner
×1
Hinge Plate 1 x 2 with 3 Fingers On Side
×1
Hinge Plate 1 x 2 with 3 Fingers On Side
×1
Brick 2 x 6
×1
Plate Special 1 x 2 Side Handle [Free Ends]
×1
Plate Special 1 x 2 Side Handle [Free Ends]
×1
Baseplate Raised 32 x 32 with Ramp and Pit, Crater Print
×1
Tile Special 1 x 1 with Clip and Straight Tips
×1
Support 6 x 6 x 10 Stanchion
×1
Brick 1 x 1
×1
Plate 2 x 4
×1
Plate 2 x 3
×1
Plate 4 x 4
×1
Plate 2 x 8
×1
Plate 4 x 8
×1
Tile 2 x 2 with Groove
×1
Tile 2 x 2 with Blue Screen, Silver and Red Panel Print
×1
Plate 1 x 8
×1
Plate 1 x 3
×1
Plate 1 x 3
×1
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×1
Slope Inverted 33° 3 x 2, No Connections between Studs, Ovoid Bottom Pin
×1
Hinge Brick 1 x 4 [Upper]
×1
Hinge Brick 1 x 4 [Lower]
×1
Hinge Brick 1 x 2 Base
×1
Brick Round 2 x 2 with Axle Hole
×1
Brick Round 2 x 2 with Axle Hole
×1
Weapon Gun / Torch (Space) [with Grooves]
×1
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×1
Panel 1 x 4 x 3 [Solid Studs]
×1
Plate 2 x 16
×1

