
Robo-Guardian
미니피규어 (3)
부품 목록 (114)

Brick Round 1 x 1 Open Stud
×16
Plate Round 1 x 1 with Solid Stud
×12
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×10
Slope Inverted 45° 2 x 1
×10
Wheel Hard Plastic Small (22mm D. x 24mm)
×10
Brick 2 x 2 Corner
×8
Tile Special 1 x 2 Grille with Bottom Groove
×8
Plate 2 x 4
×8
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×8
Brick 1 x 2
×7
Plate 1 x 2
×7
Plate 1 x 2
×7
Wedge Plate 3 x 6 Cut Corners
×6
Tile 1 x 4 with Groove
×6
Slope 45° 2 x 1 with Bottom Pin
×6
Cone 1 x 1 [No Top Groove]
×6
Technic Brick 1 x 1 with Pin Hole
×6
Hinge Plate 1 x 4 Swivel Top / Base - Solid Clip [Complete Assembly]
×6
Brick Special 1 x 2 with Grille
×5
Brick 1 x 4
×5
Slope 45° 2 x 4
×5
Slope 45° 2 x 2
×5
Plate 1 x 4
×5
Wedge Plate 3 x 4 without Stud Notches
×5
Tile Special 1 x 2 Grille with Bottom Groove
×4
Plate Special 2 x 2 with 1 Pin Hole [Split Underside Ribs]
×4
Brick Special 1 x 2 with Pin
×4
Wedge Sloped Inverted 3 x 3 x 2 Facet
×4
Brick 1 x 2
×4
Brick 1 x 6
×4
Plate 1 x 1
×4
Brick 1 x 3
×4
Technic Pin without Friction Ridges Lengthwise
×4
Plate 1 x 4
×4
Plate 2 x 6
×4
Brick Special 1 x 2 x 2/3 with Studs on Sides
×4
Brick Special 2 x 2 with Pin and No Axle Hole
×4
Plate Round 1 x 1 with Solid Stud
×4
Brick 2 x 2
×3
Tile 2 x 2 with Blue Screen, Silver and Red Panel Print
×3
Tile 1 x 2 with Blue Screen, Red and Silver Panel Print
×3
Panel 1 x 4 x 3 [Hollow Studs]
×3
Dish 2 x 2 Inverted [Radar]
×3
Wedge Plate 3 x 6 Cut Corners
×2
Plate 2 x 2 Corner
×2
Plate 2 x 2 Corner
×2
Wedge 3 x 3 Facet
×2
Wedge 3 x 3 Facet
×2
Antenna 8H Whip
×2
Technic Slope Long 1 x 6 with 3 Pin Holes
×2
Brick 2 x 3
×2
Plate 2 x 4
×2
Plate 2 x 3
×2
Plate 2 x 2
×2
Plate 2 x 2
×2
Plate 1 x 1
×2
Tile 1 x 2 with Arrow Short Yellow without Black Border Print
×2
Engine - Smooth, Small 1 x 2 Side Plate [With Axle Holders]
×2
Plate 1 x 3
×2
Technic Axle and Pin Connector
×2
Slope Inverted 45° 2 x 1
×2
Plate 1 x 6
×2
Technic Brick 1 x 2 [1 Pin Hole]
×2
Technic Axle 8
×2
Technic Bush
×2
Plate 2 x 6
×2
Plate Special 1 x 2 with Handles [Flat Ends / Low Attachment]
×2
Plate Special 1 x 2 with Handles [Flat Ends / Low Attachment]
×2
Antenna 1 x 4 with Rounded Top
×2
Technic Gear 16 Tooth with Round Holes [Old Style]
×2
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×2
Plate Special 1 x 1 with Clip Light, Bar Hole [Thick Ring]
×2
Plate Special 1 x 1 with Clip Vertical [Thick U Clip]
×2
Arm Grab Jaw
×2
Slope 33° 3 x 1
×2
Brick Special 2 x 2 with Pin and No Axle Hole
×2
Bar 1 x 3 [Clip / Anti-Stud]
×2
Plate Special 1 x 1 with Clip Horizontal [Thick U Clip]
×2
Plate Round 1 x 1 with Solid Stud
×2
Magnet Cylindrical
×2
Sticker Sheet for Set 6949-1
×1
Panel 1 x 2 x 3 - Solid Studs
×1
Brick 2 x 6
×1
Plate Special 1 x 2 Side Handle [Free Ends]
×1
Magnet Holder 2 x 3
×1
Magnet Holder Tile 2 x 2 - Short Arms
×1
Technic Pin with Friction Ridges Lengthwise and Center Slots
×1
Brick 1 x 8
×1
Plate 4 x 4
×1
Plate 4 x 6
×1
Plate 4 x 8
×1
Slope 45° 2 x 2 with Spyrius Droid Image Print
×1
Slope 45° 2 x 2 with Horizon Screen Print
×1
Tile 2 x 2 with Groove
×1
Slope 33° 3 x 4
×1
Turntable 4 x 4 Square Base with Top, Complete Assembly
×1
Brick Arch 1 x 6
×1
Brick Arch 1 x 6
×1
Bracket 2 x 2 - 2 x 2
×1
Arm Grab Jaw Holder, 3 Fingers
×1

