
Saucer Centurion
미니피규어 (2)
부품 목록 (69)

Plate 1 x 2
×12
Tile Special 1 x 2 Grille with Bottom Groove
×10
Plate 1 x 2
×9
Engine - Smooth, Small 1 x 2 Side Plate [With Axle Holders]
×8
Tyre 15 x 6 Offset Tread Small
×8
Wheel 8 x 6
×8
Plate 2 x 2
×7
Plate 2 x 3
×6
Cone 1 x 1 [No Top Groove]
×6
Plate Round 1 x 1 with Solid Stud
×6
Tile 1 x 4 with Groove
×5
Brick Round 2 x 2 with Axle Hole
×5
Wing, Tail 4 x 1 x 3
×4
Wedge Plate 10 x 10 with 4x4 Cutout and Cut Corner
×4
Wedge Plate 10 x 10 with 4x4 Cutout and Cut Corner
×4
Antenna 8H Whip
×4
Slope 33° 3 x 4
×4
Technic Brick 1 x 2 [1 Pin Hole]
×4
Plate 2 x 6
×4
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×4
Plate Special 2 x 2 with Wheel Holders
×4
Slope 45° 2 x 2
×3
Tile 2 x 2 with Blue Screen, Silver and Red Panel Print
×3
Wedge Plate 3 x 6 Cut Corners
×2
Hinge Bar with 3 Fingers and End Stud (Control Lever)
×2
Hinge Plate 1 x 2 with 3 Fingers On Side
×2
Windscreen 10 x 4 x 2 1/3 Canopy
×2
Plate Special 1 x 2 Side Handle [Free Ends]
×2
Tile Special 1 x 1 with Clip and Straight Tips
×2
Hinge Bar 2.5L with 2 and 3 Fingers on Ends (Pantograph Shoe Holder)
×2
Brick 1 x 8
×2
Plate 2 x 4
×2
Tile 1 x 2 with Groove
×2
Tile 1 x 2 with Arrow Short Yellow without Black Border Print
×2
Tail 4 x 2 x 2
×2
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×2
Technic Pin without Friction Ridges Lengthwise
×2
Plate 1 x 4
×2
Plate 1 x 4
×2
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×2
Plate 2 x 6
×2
Plate Special 1 x 2 with Handles [Flat Ends / Low Attachment]
×2
Brick Round 2 x 2 with Axle Hole
×2
Cone 2 x 2 x 2, Open Stud
×2
Cone 2 x 2 x 2, Open Stud
×2
Bracket 2 x 2 - 2 x 2
×2
Plate Special 1 x 1 with Clip Light, Bar Hole [Thick Ring]
×2
Hinge Plate 1 x 2 with 2 Fingers and Hollow Studs
×2
Hinge Plate 1 x 2 with 2 Fingers and Hollow Studs
×2
Hinge Vehicle Roof Holder 1 x 4
×2
Technic Axle 3
×2
Plate Special 1 x 2 with Long Stud Receptacle (Space Wing)
×2
Dish 2 x 2 Inverted [Radar]
×2
Dish 2 x 2 Inverted [Radar]
×2
Plate Special 1 x 1 with Clip Horizontal [Thick U Clip]
×2
Brick 2 x 4 x 2 with Holes on Sides, Reinforced Supports between Tubes
×2
Brick 1 x 10
×2
Crane Arm Outside, Wide, 15 Studs, End Notch
×1
Crane Arm Centre, 16 x 2 x 1
×1
Tool Chainsaw / Drill Body
×1
Brick 1 x 2
×1
Plate 4 x 12
×1
Plate 2 x 8
×1
Slope 45° 2 x 2 with Horizon Screen Print
×1
Plate 1 x 6
×1
Tile 1 x 8 with Groove
×1
Plate Special 1 x 2 with Bar Up [Horizontal Arm 6mm]
×1
Bracket 8 x 2 x 1 1/3
×1
Bar 1 x 6 [Closed Studs]
×1
