
Sonic Stinger with Promotional Mask
미니피규어 (1)
부품 목록 (48)

Plate 1 x 4
×6
Tile Special 1 x 1 with Clip and Straight Tips
×5
Antenna 8H Whip
×4
Support Leg Small [Insectoids]
×4
Slope 33° 3 x 1
×4
Slope Inverted 34° 3 x 1 without Internal Stopper
×4
Cone 1 x 1 [No Top Groove]
×4
Dish 2 x 2 Inverted [Radar]
×3
Plate 2 x 2 Corner
×2
Arm Holder Brick 1 x 2 with 2 Horizontal Fingers
×2
Equipment Space Scanner
×2
Dome Hemisphere 4 x 4 Multifaceted
×2
Plate Special 1 x 2 with 4 x 4 disk at 90 degrees
×2
Plate 2 x 2
×2
Slope 45° 2 x 2
×2
Slope 45° 2 x 1 with Bottom Pin
×2
Slope 45° 2 x 1 with Bottom pin, with Black Crosshairs and Green Insectoid Print
×2
Engine - Smooth, Small 1 x 2 Side Plate [With Axle Holders]
×2
Plate 1 x 3
×2
Slope Inverted 45° 2 x 1
×2
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×2
Hinge Brick 1 x 2 Base
×2
Hinge Brick 1 x 2 Top Plate Thin
×2
Plate Special 1 x 1 with Clip Light, Bar Hole [Thick Ring]
×2
Arm Piece 90° Turn [2 / 3 Fingers]
×2
Flexible Hose 8.5L with Tabbed Ends (Ends same color as Tube)
×2
Brick Special 1 x 2 with Pin
×1
Antenna 8H Whip
×1
Magnet Holder 2 x 3
×1
Plate 2 x 3
×1
Rock 2 x 2 Crystal 3 Point
×1
Plate 1 x 2
×1
Plate 1 x 2
×1
Plate 1 x 2
×1
Wing Insectoid Large with Arm Hinge and Circuitry Print Left (Print on Top, Tip on Left, Logo at Back Edge)
×1
Wing Insectoid Large with Arm Hinge and Circuitry Print Right (Print on Top, Tip on Right, Logo at Back Edge)
×1
Plate 1 x 1
×1
Tile 2 x 2 with Insectoid Logo in Triangle Print
×1
Plate 2 x 6
×1
Plate 2 x 10
×1
Engine, Strakes, 2 x 2 Thin Top Plate
×1
Brick Special 1 x 2 x 2/3 with Studs on Sides
×1
Tail 4 x 2 x 2, Rocket
×1
Wedge Plate 3 x 4 without Stud Notches
×1
Light and Sound Unit, Insectoid Tail 4 x 20 x 3
×1
Magnet Cylindrical
×1
Sticker Sheet for Sets 2964-1, 2965-1, 5316-1, 6817-1, 6837-1, 6903-1, 6905-1, 6907-1, 6909-1, 6919-1, 6969-1, 6977-1
×1Play Gear, Mask, Hard Plastic, Insectoids
×1