
Bi-Wing Blaster
미니피규어 (2)
부품 목록 (58)

Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×5
Tile Special 1 x 1 with Clip and Straight Tips
×4
Support Leg Small [Insectoids]
×4
Engine - Smooth, Small 1 x 2 Side Plate [With Axle Holders]
×4
Plate Special 1 x 1 with Clip Light, Bar Hole [Thick Ring]
×4
Arm Piece 90° Turn [2 / 3 Fingers]
×4
Plate Round 1 x 1 with Solid Stud
×4
Plate Special 1 x 4 Offset with Bar Holes
×3
Wedge Sloped 4 x 4 Triple, No Stud Notches
×3
Tile Special 1 x 2 Grille with Bottom Groove
×2
Plate 2 x 2 Corner
×2
Wedge 3 x 3 Facet
×2
Antenna 8H Whip
×2
Magnet Holder 2 x 3
×2
Arm Holder Brick 1 x 2 with 2 Horizontal Fingers
×2
Plate 2 x 4
×2
Plate 2 x 3
×2
Rock 2 x 2 Crystal 3 Point
×2
Wing Insectoid Small with Arm Hinge and Circuitry Print Right (Print on Top, Tip at Right, Logo at Back Edge)
×2
Wing Insectoid Small with Arm Hinge and Circuitry Print Left (Print on Top, Tip at Left, Logo at Back Edge)
×2
Slope 45° 2 x 2
×2
Tile 2 x 2 with Insectoid Logo in Triangle Print
×2
Tile 1 x 2 with Mars Orbit Display Print
×2
Brick 1 x 3
×2
Technic Brick 1 x 4 [3 Pin Holes]
×2
Plate 1 x 4
×2
Weapon Gun / Torch (Space) [with Grooves]
×2
Slope Inverted 34° 3 x 1 without Internal Stopper
×2
Cone 1 x 1 [No Top Groove]
×2
Tap 1 x 1 with Hole in Spout
×2
Arm Piece with Pin, 2 Fingers
×2
Magnet Cylindrical
×2
Sticker Sheet for Sets 2964-1, 2965-1, 5316-1, 6817-1, 6837-1, 6903-1, 6905-1, 6907-1, 6909-1, 6919-1, 6969-1, 6977-1
×2
Wedge Plate 3 x 6 Cut Corners
×1
Plate Special 2 x 2 with 1 Pin Hole [Split Underside Ribs]
×1
Brick 2 x 6
×1
Technic Pin with Friction Ridges Lengthwise and Center Slots
×1
Brick 1 x 2
×1
Brick 2 x 8
×1
Plate Special 2 x 6 with 4 x 8 Half Saucer
×1
Plate 2 x 3
×1
Plate 2 x 2
×1
Plate 2 x 2
×1
Plate 1 x 2
×1
Plate 4 x 6
×1
Slope 45° 2 x 2
×1
Plate Special 3 x 2 with Rounded End, Hole
×1
Slope 33° 3 x 2
×1
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×1
Plate 2 x 6
×1
Plate 2 x 16
×1
Wedge Sloped Inverted 6 x 4 with 2 Stud Connections
×1
Wedge Plate 3 x 4 without Stud Notches
×1
Slope Inverted 45° 4 x 2 Double with 2 x 2 Recessed
×1
Brick Special 2 x 2 with Pin and Axle Hole
×1
Plate Round 1 x 1 with Solid Stud
×2
Technic Pin with Friction Ridges Lengthwise and Center Slots
×1
Tap 1 x 1 with Hole in Spout
×1
