
Ice-Sat V
미니피규어 (1)
부품 목록 (72)

Technic Pin without Friction Ridges Lengthwise
×8
Wheel Hard Plastic Small (22mm D. x 24mm)
×8
Plate Round 1 x 1 with Solid Stud
×8
Plate 1 x 2
×5
Plate Special 2 x 2 with 2 Pin Holes
×4
Lever Small Base with Black Lever
×4
Plate Special 1 x 1 with Clip Vertical [Thick U Clip]
×4
Tile Special 1 x 2 Grille with Bottom Groove
×3
Plate 2 x 4
×3
Brick Round 2 x 2 with Axle Hole
×3
Hinge Vehicle Roof Holder 1 x 4
×3
Tile Special 1 x 2 Grille with Bottom Groove
×2
Wedge Plate 3 x 6 Cut Corners
×2
Hinge Bar with 3 Fingers and End Stud (Control Lever)
×2
Wedge 3 x 3 Facet
×2
Hinge Panel 2 x 4 x 3 1/3
×2
Plate 2 x 2
×2
Plate 1 x 2
×2
Tile 1 x 2 with Arrow Short Yellow with Black Border Print
×2
Tile 1 x 2 with Blue and Yellow Control Panel Print
×2
Plate 1 x 3
×2
Technic Brick 1 x 2 [1 Pin Hole]
×2
Plate 1 x 4
×2
Brick Round 2 x 2 with Axle Hole
×2
Brick Special 1 x 1 with Headlight
×2
Slope Inverted 45° 4 x 2 Double with 2 x 2 Recessed
×2
Sports Ski with Hinge
×2
Plate Round 1 x 1 with Solid Stud
×2
Magnet Cylindrical
×2
Plate 2 x 12
×1
Hinge Plate 1 x 2 with 3 Fingers On Side
×1
Windscreen 4 x 4 x 4 1/3 Helicopter
×1
Tool Chainsaw / Drill Body
×1
Antenna 8H Whip
×1
Magnet Holder 2 x 3
×1
Magnet Holder Tile 2 x 2 - Short Arms
×1
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×1
Brick 2 x 4
×1
Plate 2 x 3
×1
Plate 2 x 2
×1
Plate 1 x 2
×1
Plate 4 x 12
×1
Plate 2 x 8
×1
Slope 45° 2 x 2
×1
Tile 2 x 2 with Ice Planet 2002 Logo, Globe with Ice Print
×1
Hinge Plate 2 x 5 with Large Hole [Complete Assembly]
×1
Turntable 2 x 2 Plate - Top
×1
Turntable 2 x 2 Plate, Base
×1
Technic Axle 12
×1
Plate 1 x 4
×1
Plate 2 x 6
×1
Steering Stand 1 x 2 with Black Steering Wheel
×1
Plate Special 1 x 2 with Handles [Flat Ends / Low Attachment]
×1
Plate Special 1 x 2 with Handles [Flat Ends / Low Attachment]
×1
Cone 2 x 2 x 2, Open Stud
×1
Cone 4 x 4 x 2, Axle Hole [Plain]
×1
Antenna 1 x 4 with Rounded Top
×1
Hinge Plate 1 x 2 with 2 Fingers and Hollow Studs
×1
Hinge Plate 1 x 2 with 2 Fingers and Hollow Studs
×1
Hinge Plate 1 x 6 with 2 and 3 Fingers On Ends
×1
Cone 1 x 1 [No Top Groove]
×1
Plate Special 1 x 4 Offset with Bar Holes
×1
Brick Round 2 x 2 x 2 with Axle Hole and Fins
×1
Plate Special 1 x 2 with Bar Up [Horizontal Arm 6mm]
×1
Bracket 8 x 2 x 1 1/3
×1
Brick Special 1 x 1 Studs on 4 Sides
×1
Bar 1 x 3 [Clip / Anti-Stud]
×1
Dish 2 x 2 Inverted [Radar]
×1
Dish 2 x 2 Inverted [Radar]
×1
Tool Chainsaw Blade
×1
Plate Round 1 x 1 with Solid Stud
×1
Plate Round 1 x 1 with Solid Stud
×1