
Ogel Control Center
미니피규어 (2)
부품 목록 (131)

Plate Round 1 x 1 with Solid Stud
×25
Brick 1 x 2 x 5 with Blocked Open Studs and Bottom Stud Holder with Asymmetric Ridges
×15
Tile Special 1 x 2 Grille with Bottom Groove
×12
Slope 45° 2 x 1 with Bottom Pin
×10
Brick 1 x 2
×9
Cone 1 x 1 [No Top Groove]
×9
Tile Special 1 x 2 Grille with Bottom Groove
×8
Tile 1 x 4 with Groove
×8
Brick Special 1 x 4 with Groove
×8
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×8
Hinge Brick 1 x 2 Base
×7
Lever Small Base with Black Lever
×6
Plate 1 x 2
×6
Slope 45° 2 x 2
×6
Plate 1 x 8
×6
Slope Inverted 45° 2 x 1
×6
Tile 1 x 8 with Groove
×6
Brick 2 x 2 Corner
×5
Brick Special 1 x 2 with Pin
×5
Brick 1 x 4
×5
Plate 2 x 2
×5
Minifig Head Skeleton, Standard Skull Print
×5
Plate 1 x 6
×5
Technic Brick 1 x 2 [1 Pin Hole]
×5
Hinge Tile 1 x 4
×5
Tile 1 x 6 with Groove
×5
Hinge Panel 2 x 4 x 3 1/3
×4
Brick 1 x 1
×4
Brick 1 x 1
×4
Brick 1 x 6
×4
Brick 1 x 6
×4
Plate 1 x 2
×4
Slope 45° 2 x 2
×4
Slope 45° 2 x 1 with Bottom Pin
×4
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×4
Plate 1 x 4
×4
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×4
Plate 2 x 6
×4
Panel 1 x 2 x 1 [Square Corners]
×4
Brick Special 2 x 2 with Pin and Axle Hole
×4
Tile Special 2 x 2 with Top Pin
×3
Plate Special 1 x 2 Side Handle [Free Ends]
×3
Brick 2 x 2
×3
Brick Round 2 x 2 x 1 2/3 Dome Top, Blocked Open Stud
×3
Plate 2 x 4
×3
Slope Inverted 45° 6 x 4 Double with 4 x 4 Recessed
×3
Plate 2 x 8
×3
Technic Brick 1 x 4 [3 Pin Holes]
×3
Cone 4 x 4 x 2, Axle Hole [Plain]
×3
Support 2 x 4 x 5 Stanchion Inclined [5mm wide posts]
×3
Hinge Brick 2 x 2 Top Plate Thin
×3
Tail Shuttle
×3
Windscreen 6 x 6 Octagonal Canopy with Axle hole
×2
Plate 2 x 2 Corner
×2
Plate Special 2 x 2 with 1 Pin Hole [Split Underside Ribs]
×2
Brick 1 x 1 x 5 with Blocked Open or Hollow Stud
×2
Plate Special 6 x 8 Trap Door Frame Horizontal
×2
Plate Special 4 x 6 x 2/3 with Trap Door Hinge
×2
Fence Spindled 1 x 4 x 2 [2 Top Studs]
×2
Slope 55° 1 x 6 x 5
×2
Bar 1 x 8 with Brick 1 x 2 Curved Top End (Original, No Axle Holder)
×2
Wedge Plate 4 x 4 Cut Corner
×2
Hinge Brick 1 x 2 Locking with 2 Fingers Horizontal End, 9 Teeth
×2
Hinge Brick 1 x 2 Locking with 1 Finger Horizontal End
×2
Plate 1 x 3
×2
Plate 1 x 4
×2
Technic Axle Pin without Friction Ridges Lengthwise
×2
Plate 2 x 6
×2
Plate Special 1 x 2 with Handles [Flat Ends / Low Attachment]
×2
Hinge Brick 1 x 2 Top Plate Thin
×2
Brick Special 1 x 1 with Headlight
×2
Plate Special 1 x 1 with Clip Light, Bar Hole [Thick Ring]
×2
Tile Round 2 x 2 with Red Fan Print
×2
Plate Special 8 x 8 with Grille [No Hole in Center]
×2
Slope 33° 3 x 1
×2
Slope 33° 3 x 1
×2
Slope Inverted 34° 3 x 1 without Internal Stopper
×2
Box 2 x 2 x 2 [Hollow Studs]
×2
Box 2 x 2 x 2 Door with Slot
×2
Weapon Pike / Spear Round End
×2
Plate Round Corner 6 x 6
×2
Wedge Plate 6 x 6 Cut Corner
×2
Hinge Brick 1 x 2 Locking with Single Finger On Top
×2
Rubber Band 15mm [Square Cross Section]
×1
Tipper Bed Small, 3 x 4 Anti-studs
×1
Plate Special 1 x 2 Side Handle [Free Ends]
×1
Antenna 8H Whip
×1
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×1
Brick 2 x 4
×1
Brick 1 x 6
×1
Brick Special 1 x 4 Palisade [aka Log]
×1
Brick Special 1 x 2 with Handle
×1
Panel 3 x 6 x 6 Sloped with Window
×1
Plate 4 x 4
×1
Plate 4 x 6
×1
Propeller 3 Blade 9 Diameter
×1
Plate 4 x 8
×1
Plate 4 x 8
×1
Plate 6 x 8
×1
Windscreen 7 x 4 x 1 2/3 with Hinges
×1
