
Stingray Stormer
미니피규어 (3)
부품 목록 (114)

Tile Special 1 x 2 Grille with Bottom Groove
×18
Plate Round 1 x 1 with Solid Stud
×18
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×15
Plate 2 x 2
×14
Slope 33° 3 x 2
×13
Brick Round 2 x 2 with Axle Hole
×13
Tile 1 x 4 with Groove
×11
Brick Round 1 x 1 Open Stud
×10
Brick 1 x 2
×9
Plate 2 x 4
×8
Minifig Footwear Flipper [Thin]
×8
Propeller 3 Blade 3 Diameter with Axle Cross
×8
Slope 45° 2 x 2
×7
Tile Special 1 x 1 with Clip and Straight Tips
×6
Plate 1 x 2
×6
Slope 33° 3 x 2 with Stingrays 3 Black Arcs and White Circles Print
×6
Technic Axle Pin without Friction Ridges Lengthwise
×6
Arm Grab Jaw
×6
Wedge Plate 6 x 6 Cut Corner
×6
Brick 1 x 2
×5
Plate 1 x 2
×5
Tile 2 x 2 with Aquazone Silver and Copper Circular Print
×5
Wedge Plate 3 x 6 Cut Corners
×4
Plate 2 x 2 Corner
×4
Brick 2 x 2
×4
Brick 2 x 2
×4
Plate Special 2 x 6 with 4 x 8 Half Saucer and Stingray Print
×4
Panel 10 x 10 x 2 2/3 Quarter Saucer Base
×4
Plate 2 x 8
×4
Slope 45° 2 x 1 with Bottom Pin
×4
Tile 1 x 2 with Copper and White Circuitry, Red Rectangle and 4 Squares Print
×4
Turntable 2 x 2 Plate - Top
×4
Turntable 2 x 2 Plate, Base
×4
Plate Special 1 x 2 with Bar Up [Horizontal Arm 6mm]
×4
Panel 1 x 2 x 1 [Square Corners]
×4
Weapon Harpoon [4 Grooves on Shaft]
×4
Propeller Housing
×4
Wedge, Plate 16 x 14 Shuttle
×4
Tile 1 x 6 with Groove
×4
Brick Special 1 x 2 with Pin
×3
Equipment Grab Jaw Holder
×3
Plate 4 x 4
×3
Plate 2 x 8
×3
Tile 2 x 2 with Yellow Arrow without Border Print
×3
Brick 2 x 2 Corner
×2
Wedge Plate 3 x 3 Cut Corner
×2
Tile Special 2 x 2 with Top Pin
×2
Plate Special 1 x 2 Side Handle [Free Ends]
×2
Plate 4 x 4 Corner
×2
Brick 2 x 4
×2
Brick 2 x 2
×2
Brick 2 x 8
×2
Plate 4 x 10
×2
Slope 45° 2 x 4
×2
Rock 1 x 1 Crystal 5 Point
×2
Slope 45° 2 x 2 with Red Square and Circuitry Print
×2
Slope 45° 2 x 1 Triple with Ovoid Bottom Pin
×2
Tile 2 x 2 with Groove
×2
Tile 1 x 2 with Groove
×2
Technic Axle 2 Notched
×2
Slope 33° 3 x 4
×2
Plate 6 x 14
×2
Brick 1 x 3
×2
Plate 1 x 3
×2
Hinge Plate 2 x 4 with Articulated Joint - Male
×2
Hinge Plate 2 x 4 with Articulated Joint - Female
×2
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×2
Technic Brick 1 x 2 [1 Pin Hole]
×2
Plate 1 x 4
×2
Wedge Plate 8 x 4 Wing Left
×2
Wedge Plate 8 x 4 Wing Right with Stud Notch
×2
Weapon Gun / Torch (Space) [with Grooves]
×2
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×2
Hinge Plate 1 x 2 with 3 Fingers [Hollow Studs]
×2
Hinge Plate 1 x 2 with 2 Fingers and Hollow Studs
×2
Plate Special 1 x 4 Offset with Bar Holes
×2
Wedge Plate 3 x 4 without Stud Notches
×2
Hose, Pneumatic 4mm D. 20L / 16cm
×2
Brick Special Octagonal 2 x 3 x 1 2/3 Sloped
×2
Brick Special Octagonal 2 x 2 x 3 1/3 Corner
×2
Wedge Sloped 4 x 4 Triple, No Stud Notches with White Dots and Hydraulic Print (Stingray Engine)
×2
Wedge 3 x 2 Right
×2
Wedge 3 x 2 Left
×2
Magnet Cylindrical
×2
Equipment Control Panel
×1
Tile Special 1 x 2 with Handle
×1
Animal Body Part, Shark Body, without Bottom Tube
×1
Animal Body Part, Shark Head
×1
Magnet Holder 2 x 3
×1
Magnet Holder Tile 2 x 2 - Tall Arms with Deep Notch
×1
Brick 2 x 3
×1
Brick 2 x 10
×1
Animal, Manta Ray
×1
Brick 1 x 4
×1
Panel 10 x 10 x 2 1/3 Quarter Saucer Top with Stingray Print Left (teardrop at front & points left)
×1
Panel 10 x 10 x 2 1/3 Quarter Saucer Top with Stingray Print Right (teardrop at front & points right)
×1
Plate 2 x 3
×1
Wedge, Plate 7 x 12 Wing Right
×1
Wedge, Plate 7 x 12 Wing Left
×1
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×1

