
Sea Scorpion
미니피규어 (3)
부품 목록 (94)

Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×19
Slope 45° 2 x 2
×18
Tile Special 1 x 2 Grille with Bottom Groove
×14
Brick 1 x 2
×11
Tile Special 1 x 1 with Clip and Straight Tips
×10
Weapon Harpoon [4 Grooves on Shaft]
×8
Plate 2 x 2
×7
Plate 1 x 2
×6
Arm Grab Jaw
×6
Minifig Footwear Flipper [Thin]
×6
Plate Round 1 x 1 with Solid Stud
×6
Wedge Plate 3 x 6 Cut Corners
×5
Brick 2 x 4
×5
Tile 2 x 2 with Groove
×5
Brick Round 2 x 2 with Axle Hole
×5
Plate Special 1 x 2 with Bar Up [Horizontal Arm 6mm]
×5
Propeller 3 Blade 3 Diameter with Axle Cross
×5
Brick 1 x 1
×4
Slope 45° 2 x 1 with Bottom Pin
×4
Technic Beam 1 x 5 Thin
×4
Arm Piece Straight with 2 and 3 Fingers
×4
Brick 1 x 3
×4
Brick 1 x 10
×4
Brick 1 x 4
×3
Slope 45° 2 x 4
×3
Tile 2 x 2 with Aquazone Silver and Copper Circular Print
×3
Tile 1 x 2 with Copper and White Circuitry, Red Rectangle and 4 Squares Print
×3
Plate 1 x 3
×3
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×3
Technic Brick 1 x 2 [1 Pin Hole]
×3
Plate 1 x 4
×3
Technic Axle Pin without Friction Ridges Lengthwise
×3
Wedge Plate 8 x 4 Wing Left
×3
Wedge Plate 8 x 4 Wing Right with Stud Notch
×3
Propeller Housing
×3
Brick 2 x 2 Corner
×2
Wedge Plate 10 x 10 with 4x4 Cutout and Cut Corner
×2
Plate 2 x 2 Corner
×2
Tile 1 x 4 with Groove
×2
Tile Special 2 x 2 with Top Pin
×2
Plate Special 2 x 2 with Pin on Bottom
×2
Plate Special 1 x 2 Side Handle [Free Ends]
×2
Lever Small Base with Light Gray Lever
×2
Arm Holder Brick 1 x 2 with 2 Horizontal Fingers
×2
Brick 1 x 4
×2
Brick 1 x 4
×2
Plate 2 x 4
×2
Plate 2 x 3
×2
Rock 1 x 1 Crystal 5 Point
×2
Brick Round 1 x 1 Open Stud
×2
Tile 1 x 2 with Arrow Short Yellow without Black Border Print
×2
Plate 1 x 8
×2
Technic Pin without Friction Ridges Lengthwise
×2
Turntable 2 x 2 Plate - Top
×2
Turntable 2 x 2 Plate, Base
×2
Weapon Dagger / Knife
×2
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×2
Hinge Brick 1 x 4 [Upper]
×2
Hinge Brick 1 x 4 [Lower]
×2
Brick Special 1 x 1 with Headlight
×2
Arm Piece 90° Turn [2 / 3 Fingers]
×2
Arm Grab Jaw Holder, 3 Fingers
×2
Slope 33° 3 x 1
×2
Box 2 x 2 x 2 [Hollow Studs]
×2
Box 2 x 2 x 2 Door with Slot and Stingray Mechanical Print
×2
Dish 2 x 2 Inverted [Radar]
×2
Wedge Plate 6 x 6 Cut Corner
×2
Brick Special 2 x 2 with Pin and Axle Hole
×2
Technic Brick 1 x 1 with Pin Hole
×2
Equipment Control Panel
×1
Windscreen 6 x 6 Octagonal Canopy with Axle hole and Stingray Print
×1
Tile Special 1 x 2 with Handle
×1
Brick Special 1 x 2 with Pin
×1
Windscreen 10 x 4 x 2 1/3 Canopy
×1
Wing Plate Bi-level 12 x 9 (Exploriens)
×1
Brick 1 x 2
×1
Brick 1 x 6
×1
Equipment Grab Jaw Holder
×1
Cockpit 6 x 6 x 3 1/3 Octagonal Canopy Base
×1
Plate 1 x 2
×1
Plate 4 x 4
×1
Plate 4 x 6
×1
Slope 45° 2 x 2 with Red Square and Circuitry Print
×1
Slope 33° 3 x 2 with Stingrays 3 Black Arcs and White Circles Print
×1
Hinge Plate 2 x 4 with Articulated Joint - Male
×1
Hinge Plate 2 x 4 with Articulated Joint - Female
×1
Slope Inverted 33° 3 x 2, No Connections between Studs, Ovoid Bottom Pin
×1
Wedge Plate 4 x 4 Wing Right
×1
Wedge Plate 4 x 4 Wing Left
×1
Plate Special 1 x 1 with Clip Light, Bar Hole [Thick Ring]
×1
Hinge Vehicle Roof Holder 1 x 4
×1
Wedge Plate 3 x 4 without Stud Notches
×1
Hose, Pneumatic 4mm D. 19L / 15.2cm
×1
Plate Round 1 x 1 with Solid Stud
×1

