
F1 Driver with McLaren Race Car
미니피규어 (1)
부품 목록 (53)

Plate 1 x 2
×6
Tile Round 2 x 2 with Hole with Orange Circles print
×4
Bracket 1 x 2 - 2 x 2
×4
Wheel Rim 24 x 12 with Black Tyre
×4
Slope Curved 4 x 1 No Studs [Stud Holder with Symmetric Ridges]
×3
Slope Curved 2 x 1 No Studs [1/2 Bow]
×2
Slope Curved 2 x 1 No Studs [1/2 Bow]
×2
Panel 1 x 4 x 1 with Rounded Corners [Thin Wall]
×2
Bar Holder with Hole and Bar Handle
×2
Tile Round 1 x 1 Quarter
×2
Brick Curved 2 x 2, Two Top Studs
×2
Plate 1 x 2
×2
Plate 1 x 8
×2
Plate Special 1 x 2 Rounded with 2 Open Studs
×2
Plate Special 1 x 2 [Open O Top Clip]
×2
Plate Special 2 x 2 with Wheels Holder Wide - Technic Pins
×2
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×2
Plate Special 1 x 1 with Clip Vertical [Thick Open O Clip]
×2
Slope 18° 2 x 1 x 2/3 with 4 Slots / Grate
×2
Wheel Arch, Mudguard, 1 1/2 x 6 x 1 [Arch Extended]
×2
Tile 1 x 3
×2
Technic Brick Special 1 x 2 with Pin Hole and 1 x 2 Plate
×2
Tile Round 1 x 2 with Racing Steering Controls print
×1
Slope Curved 2 x 2 x 2/3
×1
Plate Round 1 x 2 Half Circle with Stud (Jumper)
×1
Plate Special 1 x 2 Side Handle [Free Ends]
×1
Plate 2 x 4
×1
Plate 2 x 2
×1
Plate 1 x 1
×1
Slope 45° 2 x 2
×1
Plate Special 3 x 2 with Rounded End, Hole
×1
Technic Brick 1 x 2 with Axle Hole Type 1 [+ Opening] and Bottom Pin
×1
Plate Special 1 x 3 with 2 Studs with Groove and Inside Stud Holder (Jumper)
×1
Brick Special 2 x 6 x 1 1/3 with Axle Holes and 2 x 4 Recessed, Ridges at Underside
×1
Plate Special 2 x 2 x 2/3 with Two Studs On Side and Two Raised [Half Hollow Anti-stud] - Updated Version
×1
Technic Axle Pin with Friction Ridges Lengthwise
×1
Wedge Plate 3 x 2 Right
×1
Wedge Plate 3 x 2 Left
×1
Technic Axle 3
×1
Bracket 1 x 2 with 1 x 2 Vertical Studs
×1
Plate Special 2 x 2 with Horizontal T-Bar Underneath
×1
Wedge Plate 2 x 4
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Hose Rigid 3mm D. 11L / 8.8cm
×1
Plate Special 1 x 3 Rounded with 3 Open Studs
×1
Plate 1 x 5
×1
Slope Brick Curved 2 x 4 x 2/3 No Studs with Black 'McLaren' print
×1
Slope Curved 4 x 2 No Studs with McLaren Logo, Silver/Black Stripes print
×1
Headwear Accessory Visor For Standard Helmet
×1
Tile Round 1 x 1 Quarter
×1
Plate 1 x 1
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1