
Mining Power Splitter
미니피규어 (1)
부품 목록 (88)

Technic Pin without Friction Ridges Lengthwise
×4
Wheel 18 x 14 with Pin Hole, Fake Bolts and Shallow Spokes
×4
Tyre 30.4 x 14 Offset Tread [Centre Band]
×4
Bracket 1 x 2 - 1 x 2 Inverted
×4
Plate 2 x 2
×3
Tile 2 x 2 with Groove
×3
Tile Round 2 x 2 with Bottom Stud Holder
×2
Slope 45° 2 x 1 with 2/3 Cutout [New Version]
×2
Lever Small Base with Black Lever
×2
Brick 1 x 2
×2
Brick 1 x 2
×2
Brick 1 x 1
×2
Plate 2 x 4
×2
Plate 2 x 3
×2
Plate Round Corner 3 x 3
×2
Hinge Brick 1 x 6 Locking with 1 Finger Vertical End and 2 Fingers Vertical End, 9 Teeth
×2
Tile 1 x 2 with Groove
×2
Plate Special 3 x 2 with Rounded End, Hole
×2
Technic Brick 1 x 8 [7 Pin Holes]
×2
Plate 1 x 4
×2
Hinge Plate 1 x 2 Locking with 1 Finger On End, without Groove
×2
Hinge Plate 1 x 2 Locking with 2 Fingers On End, with Groove, 9 Teeth
×2
Bracket 1 x 2 - 2 x 2
×2
Slope 18° 4 x 1
×2
Slope 30° 1 x 2 x 2/3
×2
Panel 1 x 2 x 3 [Side Supports / Hollow Studs]
×2
Plate Special 1 x 2 [Top Clip]
×2
Brick Round 2 x 2 [Grill]
×2
Tile Round 1 x 1
×2
Bracket 1 x 2 - 1 x 2
×2
Slope Curved 2 x 1 No Studs [1/2 Bow]
×1
Slope Curved 2 x 1 No Studs [1/2 Bow]
×1
Plate Special 1 x 2 with 5.9mm Centre Side Towball
×1
Slope Curved 2 x 2 x 2/3
×1
Slope Curved 2 x 2 x 2/3
×1
Weapon Harpoon [Smooth Shaft]
×1
Plate Round Corners 2 x 6 Double
×1
Tile Special 1 x 2 Grille with Bottom Groove
×1
Tile 1 x 4 with Groove
×1
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×1
Insect, Spider with Elongated Tail Section
×1
Brick 2 x 4
×1
Brick 1 x 2
×1
Plate 1 x 2
×1
Plate 1 x 2
×1
Plate 4 x 4
×1
Plate 4 x 6
×1
Brick Round 1 x 1 Open Stud
×1
Tile 1 x 2 with Groove
×1
Technic Axle and Pin Connector Angled #2 - 180°
×1
Brick 1 x 2 x 2 with Inside Stud Holder
×1
Technic Ball Joint
×1
Rock 1 1/3 x 1 1/3 x 1
×1
Grille Bar 1 x 4 x 1 2/3 Bull Bar, Rounded
×1
Plate 1 x 3
×1
Plate 1 x 6
×1
Technic Axle 6
×1
Plate 1 x 4
×1
Sticker Sheet for Set 60185-1
×1
Plate 2 x 6
×1
Plate 2 x 6
×1
Tool Pickaxe
×1
Plate 6 x 6
×1
Seat / Chair 2 x 2 with Center Sprue Mark
×1
Technic Pin 1/2
×1
Technic Axle Pin with Friction Ridges Lengthwise
×1
Slope 75° 2 x 1 x 3 with Hollow Stud
×1
Slope 75° 2 x 1 x 3 with Hollow Stud
×1
Plate Special 1 x 2 with Clips Horizontal [Open O Clips]
×1
Brick Special 1 x 1 with Clip Vertical [Open O Clip, Hollow Stud]
×1
Slope 18° 4 x 1
×1
Slope 65° 2 x 1 x 2
×1
Slope 18° 2 x 1 x 2/3 with 4 Slots / Grate
×1
Turntable 4 x 4 Square Base, Locking
×1
Technic Pin Connector Round [Slotted]
×1
Roll Cage 6 x 4 x 3 1/3
×1
Technic Pin with Friction Ridges Lengthwise and Towball
×1
Rubber Belt Small [15mm ID] [Round Cross Section]
×1
Tile 2 x 4 with Groove
×1
Brick Round 4 x 4 Centre Hole
×1
Brick Special 1 x 1 with Stud on 1 Side
×1
Plate Special 1 x 4 with 2 Studs
×1
Tile Round 1 x 1
×2
Weapon Harpoon [Smooth Shaft]
×1
Lever Small Base with Black Lever
×1
Technic Ball Joint
×1
Technic Pin without Friction Ridges Lengthwise
×1
Technic Pin 1/2
×1