
Gold Heist
미니피규어 (2)
부품 목록 (96)

Slope Curved 3 x 1 No Studs
×8
Plate Special 1 x 2 Side Handle [Free Ends]
×7
Technic Brick 1 x 2 [1 Pin Hole]
×7
Plate Special 1 x 1 with Clip Horizontal [Thick U Clip]
×7
Plate 1 x 2
×6
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×6
Cone 1 x 1 [No Top Groove]
×6
Technic Pin with Friction Ridges Lengthwise and Center Slots
×5
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×5
Technic Axle Pin with Friction Ridges Lengthwise
×5
Brick 1 x 2
×4
Brick Round 2 x 2 Dome Top, Blocked Open Stud, Bottom Axle Holder
×4
Technic Pin without Friction Ridges Lengthwise
×4
Technic Axle Pin without Friction Ridges Lengthwise
×4
Plate Special 1 x 1 with Clip Light, Bar Hole [Thick Ring]
×4
Tile Round 2 x 2 with Bottom Cross
×4
Plate Special 3 x 2 with Rounded End, Hole
×3
Technic Axle 3 with Stud
×3
Flag 2 x 2 Square [Thin Clips]
×2
Wing, Tail 4 x 1 x 3
×2
Bracket 1 x 2 - 1 x 4 [Square Corners]
×2
Plate Special 2 x 2 with Bar Frame Octagonal
×2
Plate 2 x 4
×2
Plate 2 x 4
×2
Plate 2 x 2
×2
Plate Round Corner 3 x 3
×2
Cylinder 3 x 6 x 2 2/3 Horizontal Hollow Studs
×2
Slope 45° 2 x 2
×2
Tile 1 x 2 with Groove
×2
Technic Beam 1 x 11.5 Double Bent Thick
×2
Technic Pin Long with Friction Ridges Lengthwise and Stop Bush [3 Lateral Holes, Big Pin Hole]
×2
Technic Beam 3 x 5 L-Shape Thick
×2
Slope 33° 3 x 2
×2
Technic Axle 4
×2
Plate 2 x 6
×2
Technic Brick 1 x 6 [5 Pin Holes]
×2
Antenna 1 x 4 with Rounded Top
×2
Technic Cylinder 4 x 4 with Pin Holes and Centre Bar, Closed Sides on Bar
×2
Bracket 1 x 2 - 2 x 2
×2
Plate Special 1 x 2 with Bar Up [Horizontal Arm 6mm]
×2
Panel 1 x 2 x 2 [Hollow Studs]
×2
Wedge Plate 2 x 4
×2
Arm Mechanical with Clip [Thin Support]
×2
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×2
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×2
Plate Special 1 x 2 with Clips Horizontal [Open O Clips]
×2
Brick Arch 1 x 12 x 3
×2
Technic Pin 1/2 with 2L Bar Extension
×2
Wave / Flame Rounded with Base Pegs
×2
Plate Round 1 x 1 with Solid Stud
×2
Plate Round 1 x 1 with Solid Stud
×2
Plate Round 1 x 1 with Solid Stud
×2
Slope Curved 4 x 1 No Studs [Stud Holder with Asymmetric Ridges]
×2
Large Figure Wing, Small
×2
Cone 3 x 3 x 2
×2
Technic Pin Connector Double with Bar [2 Holes]
×2
Flag 2 x 2 Square [Thin Clips]
×1
Tile Special 1 x 2 Grille with Bottom Groove
×1
Bracket 1 x 2 - 1 x 4 [Square Corners]
×1
Antenna 8H Whip
×1
Plate Special 2 x 2 with 2 Pin Holes
×1
Technic Beam 1 x 4 Thin with Stud Connector
×1
Brick 2 x 2
×1
Handlebars
×1
Plate Special 2 x 4 with Pins
×1
Plate 2 x 3
×1
Arm Mechanical with 2 Clips [Battle Droid]
×1
Technic Brick 1 x 2 with Axle Hole Type 2 [X Opening]
×1
Technic Bush 1/2 Smooth with Axle Hole Semi-Reduced
×1
Technic Axle and Pin Connector Toggle Joint Smooth
×1
Technic Beam 1 x 5 Thick
×1
Technic Brick 1 x 4 [3 Pin Holes]
×1
Plate 2 x 6
×1
Plate Special 1 x 2 with Handles [Flat Ends / Low Attachment]
×1
Technic Pin 1/2
×1
Brick Curved 6 x 2
×1
Wedge Plate 3 x 4 with Stud Notches
×1
Slope Curved 4 x 6 x 2/3 Triple Curved with 4 Studs
×1
Technic Axle 5.5 with Stop [Rounded Short End]
×1
Equipment Handcuffs
×1
Brick Arch 1 x 6 x 2 Curved Top
×1
Windscreen 3 x 6 x 1 Curved with 2 Circular Stud Holders in Bottom
×1
Sticker Sheet for Set 5971-1
×1
Headwear Accessory Visor For Standard Helmet
×1
Technic Pin with Friction Ridges Lengthwise and Center Slots
×1
Arm Mechanical with 2 Clips [Battle Droid]
×1
Arm Mechanical with 2 Clips [Battle Droid]
×1
Technic Bush 1/2 Smooth with Axle Hole Semi-Reduced
×1
Technic Pin without Friction Ridges Lengthwise
×1
Technic Pin 1/2
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Plate Round 1 x 1 with Solid Stud
×1
Plate Round 1 x 1 with Solid Stud
×1
Plate Round 1 x 1 with Solid Stud
×1
Equipment Handcuffs
×1
