
Ogel Sub Shark
미니피규어 (2)
부품 목록 (57)

Technic Pin with Friction Ridges Lengthwise and Center Slots
×6
Tail Shuttle
×5
Hinge Brick 2 x 2 Locking with 2 Fingers Vertical and Axle Hole, 9 Teeth
×4
Brick Special 2 x 2 x 2 with Rotation Joint Socket and Rear Pin Hole
×4
Technic Rotation Joint Ball with Arm - Pin and Hole Ends
×4
Tile Special 1 x 2 Grille with Bottom Groove
×3
Tile 1 x 4 with Groove
×3
Tile Special 1 x 2 with Handle
×3
Cone 1 x 1 [No Top Groove]
×3
Plate Special 2 x 2 with Pin on Bottom, Small Holes in Plate and Rotational Locking Fingers on Underside
×2
Brick 2 x 3
×2
Plate 1 x 2
×2
Bar 1 x 8 with Brick 1 x 2 Curved Top End (Axle Holder Inside Small End)
×2
Hinge Brick 1 x 2 Locking with 1 Finger Vertical End
×2
Hinge Brick 1 x 2 Locking with 2 Fingers Vertical End, 9 Teeth
×2
Bar 4L (Lightsaber Blade / Wand)
×2
Slope 45° 2 x 1 Triple with Ovoid Bottom Pin
×2
Hinge Cylinder 1 x 2 Locking with 1 Finger and Axle Hole On Ends
×2
Hinge Cylinder 1 x 2 Locking with 2 Click Fingers and Axle Hole, 9 Teeth
×2
Tile 2 x 2 with Groove
×2
Large Figure Weapon, Claw, Triple, with Axle
×2
Technic Brick 4 x 6 with 2 x 4 Opening
×2
Plate 1 x 6
×2
Plate 2 x 6
×2
Plate Special 1 x 1 with Clip Light, Bar Hole [Thick Ring]
×2
Propeller 8 Blade 5 Diameter
×2
Hinge Cylinder 1 x 3 Locking with 1 Finger and Technic Friction Pin with Round Hole
×2
Brick Curved 6 x 1 Inverted
×2
Wedge Plate 4 x 9 without Stud Notches
×1
Wedge Plate 3 x 6 Cut Corners
×1
Brick 1 x 2
×1
Brick Round 2 x 2 x 1 2/3 Dome Top, Blocked Open Stud
×1
Plate 2 x 3
×1
Plate 4 x 6
×1
Hinge Brick 2 x 2 Locking with 1 Finger Vertical [No Axle Hole]
×1
Slope 45° 2 x 2
×1
Technic Connector 3 x 1 x 4 with Two Pins and Click Hinge
×1
Technic Axle and Pin Connector Angled #1
×1
Technic Pin Long with Friction Ridges Lengthwise and Stop Bush [3 Lateral Holes, Big Pin Hole]
×1
Technic Axle 2 Notched
×1
Technic Axle 5
×1
Technic Bush 1/2 Smooth with Axle Hole Reduced
×1
Technic Beam 1 x 3 Thick
×1
Minifig Head Skeleton, Evil Skull Print
×1
Plate 6 x 6
×1
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×1
Wedge Curved 6 x 2 Right with Submarine Print
×1
Wedge Curved 6 x 2 Left with Submarine Print
×1
Windscreen 8 x 6 x 2 Curved with Evil Skull Logo and Windows Print
×1
Wedge Curved Inverted 8 x 6 x 2 Cockpit
×1
Wedge Curved Inverted 8 x 6 x 2 Cockpit
×1Sticker Sheet for Set 4793-1
×1
Weapon Pike / Spear Round End
×1
Technic Axle 3
×1
Panel 1 x 2 x 1 with Ogel Control Panel Print
×1
Technic Pin Long with Friction Ridges Lengthwise, 2 Center Slots
×1
Technic Bush 1/2 Smooth with Axle Hole Reduced
×1
