
Alpha Team Navigator and ROV
미니피규어 (1)
부품 목록 (51)

Technic Pin with Friction Ridges Lengthwise and Center Slots
×6
Hinge Cylinder 1 x 3 Locking with 1 Finger and 2 Fingers On Ends, without Hole, 9 Teeth
×6
Plate Special 1 x 1 with Clip Horizontal [Thick U Clip]
×6
Bar 1 x 3 [Clip / Anti-Stud]
×4
Plate Round 1 x 1 with Solid Stud
×4
Plate 2 x 2 Corner
×2
Brick Special 1 x 1 with Handle
×2
Lever Small Base with Black Lever
×2
Brick 1 x 2
×2
Plate 1 x 2
×2
Brick Special 1 x 2 with Handle
×2
Hinge Cylinder 1 x 2 Locking with 1 Finger and Axle Hole On Ends
×2
Grille 6 x 4 x 3 [2 Pins & 2 Pin Holes]
×2
Technic Axle and Pin Connector Angled #1
×2
Technic Axle 2 Notched
×2
Technic Pin without Friction Ridges Lengthwise
×2
Hinge 1 x 3 Locking with 2 Fingers and Claw End, 9 Teeth
×2
Technic Cylinder 4 x 4 with Pin Holes and Centre Bar, Closed Sides on Bar
×2
Brick Curved 6 x 1
×2
Dish 2 x 2 Inverted [Radar]
×2
Minifig Footwear Flipper [Thin]
×2
Plate Special 1 x 1 with Clip Horizontal [Thick U Clip]
×2
Propeller 3 Blade 3 Diameter with Axle Cross
×2
Tile Special 1 x 2 Grille with Bottom Groove
×1
Tile 1 x 4 with Groove
×1
Plate Special 1 x 2 Side Handle [Free Ends]
×1
Brick 2 x 4
×1
Minifig Neckwear Scuba Airtank, Bar Holder
×1
Equipment Binoculars
×1
Equipment Stretcher Holder
×1
Plate 2 x 4
×1
Plate 2 x 2
×1
Brick Special 1 x 2 with Vertical Clip [Thick U Clip]
×1
Bar 4L (Lightsaber Blade / Wand)
×1
Slope Curved 2 x 2 with Lip, No Studs with Mission Deep Sea 'TEE VEE' Print
×1
Spoiler 3 x 4 x 6
×1
Technic Brick 6 x 8 with 4 x 6 Opening
×1
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×1
Wedge Curved 6 x 2 Right, Inner Ridges
×1
Wedge Curved 6 x 2 Left, Inner Ridges
×1
Windscreen 8 x 6 x 2 Curved with Silver & Yellow Hose and Window Print
×1
Wedge Curved Inverted 6 x 2 Right
×1
Wedge Curved Inverted 6 x 2 Left
×1
Wedge Curved Inverted 8 x 6 x 2 Cockpit
×1
Engine, Strakes, 2 x 2 Thin Top Plate
×1
Equipment Camera with Side Sight [aka Space Gun]
×1
Hair Center Parting
×1
Cone 1 x 1 [No Top Groove]
×1
Plate Special 1 x 2 with Bar Up [Horizontal Arm 6mm]
×1
Plate Round 1 x 1 with Solid Stud
×2
Bar 1 x 3 [Clip / Anti-Stud]
×1