
X-wing Fighter
미니피규어 (2)

Yoda, Plain Sand Green Head
fig-003534×1

Luke Skywalker, Dagobah Outfit, Yellow Skin, Sand Green Tank Top with Neck Bracket
fig-003535×1
부품 목록 (188)

Technic Brick 1 x 2 [2 Pin Holes]
×18
Slope 45° 2 x 1 with Bottom Pin
×14
Plate 1 x 6
×13
Plate 1 x 3
×12
Technic Axle 3
×11
Technic Axle Connector Ridged [with x Hole x Orientation]
×10
Brick 1 x 2
×9
Plate 2 x 2 Corner
×8
Brick Special 1 x 2 with Grille
×8
Brick 1 x 2
×8
Brick 1 x 1
×8
Technic Pin Long without Friction Ridges - Single Slot
×8
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×8
Technic Pin with Friction Ridges Lengthwise and Towball
×8
Brick 1 x 2
×7
Plant, Sea Grass
×7
Plate 2 x 4
×7
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×7
Plate Special 1 x 1 with Clip Vertical [Thick U Clip]
×7
Tile Special 1 x 2 Grille with Bottom Groove
×6
Plate 2 x 2
×6
Plate 1 x 2
×6
Plate 1 x 6
×6
Plate Round 1 x 1 with Solid Stud
×6
Hinge Plate 1 x 4 Swivel Top / Base - Solid Clip [Complete Assembly]
×6
Rubber Belt Small [15mm ID] [Round Cross Section]
×6
Brick 1 x 4
×5
Plate 1 x 2
×5
Brick Round 2 x 2 with Axle Hole
×5
Cone 1 x 1 [No Top Groove]
×5
Plate Round 1 x 1 with Solid Stud
×5
Brick Arch 1 x 5 x 4 [Continuous Bow]
×4
Tile 1 x 4 with Groove
×4
Plate 2 x 12
×4
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×4
Technic Axle Towball
×4
Brick 1 x 1
×4
Plate 1 x 2
×4
Plate 4 x 4
×4
Bar 1 x 8 with Brick 1 x 2 Curved Top End (Axle Holder Inside Small End)
×4
Cylinder 3 x 6 x 2 2/3 Horizontal Hollow Studs
×4
Slope 45° 2 x 2
×4
Slope 45° 2 x 1 with Bottom Pin
×4
Brick Round 1 x 1 Open Stud
×4
Tile 2 x 2 with Groove
×4
Slope 33° 3 x 2
×4
Plate 1 x 3
×4
Brick Arch 1 x 4
×4
Plate 1 x 4
×4
Plate 1 x 4
×4
Technic Bush
×4
Hinge Brick 1 x 4 [Upper]
×4
Hinge Brick 1 x 4 [Lower]
×4
Brick Round 2 x 2 with Axle Hole
×4
Tile 1 x 8 with Groove
×4
Minifig Neckwear Bracket [One Stud]
×4
Slope Inverted 34° 3 x 1 without Internal Stopper
×4
Technic Axle Pin with Friction Ridges Lengthwise
×4
Plate 1 x 10
×4
Dish 2 x 2 Inverted [Radar]
×4
Dish 2 x 2 Inverted [Radar]
×4
Plate Round 1 x 1 with Solid Stud
×4
Technic Brick 1 x 1 with Pin Hole
×4
Tile 1 x 6 with Groove
×4
Plate 1 x 2
×3
Plate 4 x 6
×3
Brick Arch 1 x 6 x 2 - Thick Top with Reinforced Underside
×3
Plate 1 x 4
×3
Plate Special 1 x 2 with 1 Stud without Groove (Jumper)
×3
Panel 1 x 2 x 1 [Square Corners]
×3
Weapon Lightsaber Hilt without Bottom Ring
×2
Plate 2 x 2 Corner
×2
Tile 1 x 4 with Groove
×2
Tile 1 x 4 with Groove
×2
Tile 1 x 4 with 5 Red Stripes Print
×2
Tile Special 1 x 2 with Handle
×2
Brick 1 x 2
×2
Brick 1 x 4
×2
Plant, Round 1 x 1 - 3 Bamboo Leaves
×2
Plate 2 x 3
×2
Plate 2 x 2
×2
Plate 4 x 4
×2
Plate 4 x 6
×2
Plate 4 x 6
×2
Wedge Plate 6 x 12 Left
×2
Wedge Plate 6 x 12 Right
×2
Leg Mechanical - Droid with Technic Pin
×2
Hinge Brick 1 x 2 Locking with 1 Finger Vertical End
×2
Slope 45° 2 x 4
×2
Slope 45° 2 x 4
×2
Bar 4L (Lightsaber Blade / Wand)
×2
Brick Special 1 x 4 with 4 Studs on One Side
×2
Wedge Plate 4 x 4 Cut Corner
×2
Wedge Plate 4 x 4 Cut Corner
×2
Brick Special 1 x 2 with 2 Pins, Round Pin Holes
×2
Hinge Cylinder 1 x 2 Locking with 2 Click Fingers and Axle Hole, 9 Teeth
×2
Tile 2 x 2 with SW Rebel Mechanical Print
×2
Technic Bush 1/2 Smooth with Axle Hole Reduced
×2
Plate 1 x 8
×2
Plate 1 x 8
×2