
TIE Bomber
미니피규어 (1)
부품 목록 (61)

Plate 1 x 10
×14
Tile Special 1 x 2 Grille with Bottom Groove
×13
Plate 2 x 2
×9
Slope 45° 2 x 2
×9
Brick 1 x 2
×8
Hinge Brick 1 x 2 Locking with 1 Finger Vertical End
×8
Hinge Brick 1 x 2 Locking with 2 Fingers Vertical End, 9 Teeth
×8
Wedge Plate 4 x 4 Cut Corner
×8
Brick Round 1 x 1 Open Stud
×8
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×8
Brick Special 2 x 2 with 2 Pins and Axle Hole
×6
Brick 1 x 4
×6
Plate 1 x 6
×6
Technic Brick 1 x 4 [3 Pin Holes]
×6
Plate Round 1 x 1 with Solid Stud
×6
Plate 2 x 6
×5
Plate 2 x 3
×4
Slope Inverted 45° 6 x 4 Double with 4 x 4 Recessed
×4
Plate 4 x 12
×4
Plate 1 x 4
×4
Slope Inverted 33° 3 x 2, No Connections between Studs, Ovoid Bottom Pin
×4
Plate 2 x 10
×4
Plate Special 1 x 1 with Clip Vertical [Thick U Clip]
×4
Slope 45° 2 x 8
×4
Slope Inverted 45° 4 x 2 Double with 2 x 2 Recessed
×4
Brick Special 2 x 2 with Pin and Axle Hole
×4
Brick Special 1 x 4 with Groove
×3
Brick 2 x 2
×3
Plate 1 x 2
×3
Plate 4 x 4
×3
Slope 18° 4 x 2
×3
Brick Round 1 x 1 Open Stud
×3
Flag 2 x 2 Square [Thin Clips] with SW TIE Bomber Rectangles Print
×2
Brick Special 1 x 1 with Handle
×2
Plate 2 x 4
×2
Plate 6 x 12
×2
Plate 6 x 8
×2
Slope Inverted 65° 6 x 6 x 2 Quad with Cutouts
×2
Bar 4L (Lightsaber Blade / Wand)
×2
Plate Special 1 x 2 with Door Rail
×2
Brick Arch 1 x 6
×2
Dish 4 x 4 Inverted [Radar]
×2
Tile Round 2 x 2 with Imperial Logo Print
×2
Hinge Vehicle Roof 4 x 4
×2
Technic Pin 1/2
×2
Dish 2 x 2 Inverted [Radar]
×2
Tile 1 x 4 with Groove
×1
Brick 1 x 6
×1
Windscreen 3 x 6 x 5 Bubble with Studs on Top with Octagonal Light Gray Lines Print
×1
Launcher, Technic Competition Cannon, Round Bottom with Same Color Ends
×1
Panel 1 x 4 x 3 [Hollow Studs]
×1
Hinge Vehicle Roof Holder 1 x 4
×1
Cone 1 x 1 [No Top Groove]
×1
Hinge Tile 1 x 4
×1
Tile 1 x 6 with Groove
×1
Rubber Band Medium (Square Cross Section)
×1
Projectile, Technic Competition Arrow, Beam Shaft with Solid Black Rubber End
×1
Rubber Band Medium (Square Cross Section)
×3
Rubber Band / Belt Holder 2 x 6 x 2 1/3
×1
Technic Pin 1/2
×1
Plate Round 1 x 1 with Solid Stud
×1