
Police Helicopter
미니피규어 (2)

Policeman, Dark Blue Jacket with Pockets and Badge, White Helmet with Visor, Orange Sunglasses
fig-001492×1

Policeman, Dark Blue Jacket with Pockets and Badge, White Helmet with Visor, Sunglasses and Wavy Mouth
fig-007790×1
부품 목록 (70)

Plate Special 1 x 1 with Clip Vertical [Thick U Clip]
×6
Slope 18° 2 x 1 x 2/3 with 4 Slots / Grate
×4
Wheel Holder 2 x 2 Thin with Clips, Plane Single
×3
Wheel Centre Small with Stub Axles (Pulley Wheel)
×3
Tyre 14 x 4 Smooth Small Single [New Style]
×3
Brick Curved 10 x 1 [Symmetric Inside Ridges]
×2
Tile Special 1 x 2 Grille with Bottom Groove
×2
Plate 2 x 12
×2
Brick 1 x 2
×2
Plate 2 x 4
×2
Plate 2 x 3
×2
Plate 1 x 2
×2
Plate 1 x 1
×2
Slope 18° 4 x 2
×2
Bar 4L (Lightsaber Blade / Wand)
×2
Hinge Plate 1 x 8 Locking with Angled Side Extensions, Rounded Plate Underside, 9 Teeth
×2
Slope Inverted 45° 2 x 1
×2
Plate 1 x 6
×2
Hinge Plate 1 x 2 Locking with 1 Finger On End, with Groove
×2
Panel 1 x 2 x 1 [Square Corners]
×2
Panel 1 x 1 x 1 Corner
×2
Wheel Arch, Mudguard, 1 1/2 x 6 x 1 [Arch Extended]
×2
Panel 1 x 2 x 2 [Side Supports / Hollow Studs]
×2Sticker Sheet for Set 4473-1
×1
Wedge Plate 3 x 6 Cut Corners
×1
Tile Special 1 x 2 with Handle
×1
Plate Special 2 x 2 with 1 Pin Hole [Split Underside Ribs]
×1
Propeller 4 Blade 5 Diameter with Rounded Ends, Open Hub
×1
Brick 2 x 2
×1
Brick 1 x 2
×1
Tool Grappling Hook
×1
Slope 18° 4 x 2
×1
Slope 45° 2 x 2 with Aircraft Multiple Flight Controls Print
×1
Tile 2 x 2 with Groove
×1
Tile 1 x 1 with Groove
×1
Tile 1 x 1 with Groove
×1
Plate Special 3 x 2 with Rounded End, Hole
×1
Technic Brick 1 x 2 [2 Pin Holes]
×1
Technic Steering Arm with 2 Pins
×1
Technic Axle 5
×1
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×1
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×1
Plate 1 x 6
×1
Technic Pin without Friction Ridges Lengthwise
×1
Turntable 2 x 2 Plate - Top
×1
Turntable 2 x 2 Plate, Base
×1
Plate 1 x 4
×1
Slope Inverted 33° 3 x 2, Connections between Studs, Ovoid Bottom Pin
×1
Plate 2 x 6
×1
Plate 2 x 10
×1
Wedge Plate 4 x 2 Left
×1
Technic Axle Pin with Friction Ridges Lengthwise
×1
Wedge Sloped Inverted 4 x 4 Triple [2 Connections between Front Studs]
×1
Slope 45° 3 x 4 Double / 33°
×1
Wedge 3 x 4 [Stud Notches]
×1
Wedge 3 x 4 [Stud Notches]
×1
Engine / Air Scoop 2 x 2
×1
String Cord Thin (0.5mm) 100cm
×1
Windscreen 3 x 4 x 1 1/3 Large Glass Surface
×1
Technic Axle Connector Smooth [with x Hole + Orientation]
×1
Plate Round 1 x 1 with Solid Stud
×1
String Reel 2 x 1 x 2 Drum with Axle Hole
×1
Tail Shuttle
×1
Tile 1 x 3
×1
Slope Inverted 45° 4 x 4 Double with 4 x 2 Recessed, 2 Holes
×1
Panel 1 x 2 x 3 [Side Supports / Hollow Studs]
×1
Plate Special 1 x 2 with Bar Up [Horizontal Arm 5mm]
×1
Wedge Plate 3 x 4 with Stud Notches [Reinforced Underside]
×1
Propeller 3 Blades 5 Diameter, Pin Hole
×1
Wedge Sloped 4 x 4 Taper, with Stud Notches
×1