
The Precious Crystal Mine
미니피규어 (2)
부품 목록 (163)

Plate 1 x 3
×1
Brick Arch 1 x 4
×1
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×1
Plate 1 x 6
×1
Technic Brick 1 x 2 [1 Pin Hole]
×1
Plate 1 x 4
×1
Cone 2 x 2 x 2, Open Stud
×1
Animal Body Part / Plant, Tail / Trunk / Tentacle / Tongue / Vine / Tree Branch (Short Tip)
×1
Technic Axle 3
×1
Dish 2 x 2 Inverted [Radar]
×1
Rock Panel 2 x 4 x 6
×1
Plate Special 1 x 2 [Side Handle Closed Ends]
×1
Plate Special 1 x 1 with Tooth
×1
Cone 1 x 1 [Top Groove]
×1
Cone 1 x 1 [Top Groove]
×1
Plate Round Corner 6 x 6
×1
Brick Special 1 x 1 with Clip Vertical [Open O Clip, Hollow Stud]
×1
Technic Beam 1 x 2 Thick with Pin Hole and Axle Hole
×1
Plate Special 1 x 1 with Clip Vertical [Thick Open O Clip]
×1
Plate Special 1 x 1 with Clip Horizontal [Thick Open O Clip]
×1
Plate Round 1 x 1 with Solid Stud
×1
Plate Round 1 x 1 with Solid Stud
×1
Brick Special 2 x 2 with Pin and Axle Hole
×1
Wheel Arch, Mudguard, 1 1/2 x 6 x 1 [Arch Extended]
×1
Plate Special 1 x 2 with Clip Horizontal on End
×1
Bar 6L with Stop Ring
×1
Equipment Telescope / Torch / Spyglass, Support Round 1 x 1 x 1 2/3
×1
Flame / Headwear Accessory Plume / Feather, Triple Point
×1
Technic Axle 1.5 with Perpendicular Axle Connector (Technic Pole Reverser Handle)
×1
Hinge Plate 1 x 4 Swivel Top / Base - Solid Clip [Complete Assembly]
×1
Slope 30° 1 x 2 x 2/3
×1
Tile 2 x 4 with Groove
×1
Brick Special 1 x 1 with Stud on 1 Side
×1
Plate Special 2 x 2 with Groove and Center Stud (Jumper)
×1
Plate 8 x 16
×1
Panel 1 x 2 x 1 with Rounded Corners and Central Divider
×1
Tile Round 1 x 1
×1
Tile Round 1 x 1
×1
Tile Round 1 x 1
×1
Tile Round 1 x 1 with Magenta Octagon Print
×1
Hinge Plate 2 x 4 with Pin Hole - Top
×1
Slope 75° 2 x 2 x 3 [Solid Studs]
×1
Tile 1 x 1 with Groove
×2
Plant, Flower, Plate Round 1 x 1 with 4 Petals
×2
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×2
Tile Round 1 x 1
×2
Plant, Cherries
×1
Plate 1 x 1
×1
Tile 1 x 1 with Groove
×1
Plant, Carrot Top
×1
Plant, Flower, Plate Round 1 x 1 with 4 Petals
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Plate Round 1 x 1 with Solid Stud
×1
Plate Round 1 x 1 with Solid Stud
×1
Plate Round 1 x 1 with Solid Stud
×1
Plate Round 1 x 1 with Solid Stud
×1
Creature Body Part, Horn (Unicorn)
×1
Tile Round 1 x 1
×1
Tile Round 1 x 1
×1
Tile Round 1 x 1
×1
Tile Round 1 x 1 with Magenta Octagon Print
×1
