
Restaurants of the World: Japan
미니피규어 (1)
부품 목록 (143)

Tile Special 1 x 2 Grille with Bottom Groove
×12
Equipment Candlestick
×10
Plate 1 x 2
×8
Tile 1 x 4 with Groove
×6
Plate Special 1 x 2 Rounded with 2 Open Studs
×6
Plate 1 x 2
×5
Tile 1 x 2 with Groove
×5
Plate Special 2 x 2 with Only 2 studs
×5
Plate Special 1 x 4 Rounded with 2 Open Studs
×5
Brick Special 1 x 2 with Masonry Brick Profile
×5
Wedge Plate 2 x 2 Cut Corner
×4
Wedge Plate 2 x 2 Cut Corner
×4
Slope 45° 2 x 1 with 2/3 Inverted Cutout and no stud
×4
Slope 45° 2 x 1 with 2/3 Inverted Cutout and no stud
×4
Slope 45° 2 x 1 with 2/3 Inverted Cutout and no stud
×4
Brick 2 x 2
×4
Brick 1 x 1
×4
Brick 1 x 6
×4
Brick Special 1 x 2 Palisade [aka Log]
×4
Brick Special 1 x 2 Palisade [aka Log]
×4
Plate Special 3 x 2 with Rounded End, Hole
×4
Plate Special 2 x 2 with Only 2 studs
×4
Brick Special 1 x 2 Rounded with Center Bars
×4
Flag 2 x 2 Square, Flared Clip Edge [Thick Clips]
×4
Slope 30° 1 x 2 x 2/3
×4
Tile Round 1 x 1 with Sushi print
×4
Brick Special 1 x 2 x 1 2/3 with 4 Studs on 1 Side
×3
Tile 1 x 2 with Groove
×3
Plate 1 x 8
×3
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×3
Plant, Flower, Minifig Accessory with 7 Thick Petals and Pin, Center Ring
×3
Bar, Angled with 1 x 1 Round Plate / Stud on End
×3
Plate Round 1 x 1 with Open Stud
×3
Plate Special 1 x 2 with Clip Horizontal on Side
×2
Brick Special 1 x 4 with Masonry Brick Profile
×2
Tile Special 1 x 1 with Clip with Rounded Edges
×2
Tile Round 1 x 1 with Hollow Bar
×2
Brick 2 x 2 Corner
×2
Large Figure Weapon Lightsaber Hilt with Axle Hole and Two Bar Holders
×2
Tile Special 1 x 2 Grille with Bottom Groove
×2
Plate 2 x 2 Corner
×2
Plant, Leaves 4 x 3
×2
Tile Round 1 x 1 Half Circle
×2
Plant, Flower, Plate Round 1 x 1 with 5 Petals
×2
Tile Round 1 x 1 Quarter
×2
Container Box 2 x 2 x 1 Reinforced Bottom
×2
Brick 2 x 3
×2
Brick 1 x 2
×2
Brick 1 x 1
×2
Brick 2 x 10
×2
Plate 2 x 3
×2
Plate 6 x 10
×2
Plate 2 x 8
×2
Brick Round 1 x 1 Open Stud
×2
Tile 1 x 2 with Groove
×2
Plate Special 1 x 3 with 2 Studs with Groove and Inside Stud Holder (Jumper)
×2
Slope Inverted 45° 2 x 1
×2
Plate 1 x 6
×2
Plate 1 x 4
×2
Plate 1 x 4
×2
Equipment Candlestick
×2
Plate 2 x 6
×2
Plate 2 x 10
×2
Hinge Brick 1 x 2 Base
×2
Plate Special 1 x 4 with 2 Studs with Groove [New Underside]
×2
Technic Axle Pin with Friction Ridges Lengthwise
×2
Plate 1 x 10
×2
Slope 18° 2 x 1 x 2/3
×2
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×2
Cone 1 x 1 [Top Groove]
×2
Hinge Brick 2 x 2 Top Plate Thin
×2
Plate Round 1 x 1 with Solid Stud
×2
Plate Special 1 x 2 with Clip Horizontal on End
×2
Plate Special 1 x 2 with Clip Vertical on End
×2
Equipment Chopsticks
×2
Panel 1 x 2 x 3 [Side Supports / Hollow Studs]
×2
Plate Special 2 x 2 with Groove and Center Stud (Jumper)
×2
Tile Round 1 x 1
×2
Sticker Sheet for Set 40906-1
×1
Tile 2 x 2 Corner
×1
Tile Round 1 x 1 with Hollow Bar
×1
Brick Special 1 x 2 x 1 2/3 with 4 Studs on 1 Side
×1
Technic Pin Connector Hub with 1 Axle
×1
Slope Curved 2 x 1 with Stud Notch Right
×1
Slope Curved 2 x 1 with Stud Notch Right
×1
Slope Curved 2 x 1 with Stud Notch Left
×1
Slope Curved 2 x 1 with Stud Notch Left
×1
Brick 1 x 6
×1
Brick 1 x 4
×1
Plate 2 x 2
×1
Brick Special 1 x 2 with Vertical Clip [Open O Clip]
×1
Plate 1 x 1
×1
Bar 4L (Lightsaber Blade / Wand)
×1
Brick Round 1 x 1 Open Stud
×1
Tile 1 x 1 with Groove
×1
Technic Axle and Pin Connector Angled #3 - 157.5°
×1
Technic Plate 2 x 4 [3 Holes]
×1
Plate 2 x 6
×1
Plate 2 x 6
×1
Tile 1 x 8 with Groove
×1