
African Savanna Diorama
부품 목록 (101)

Plate Round 1 x 1 with Open Stud
×27
Wedge Plate 2 x 2 Cut Corner
×19
Plant, Plate 1 x 1 Round with 3 Leaves
×16
Plate 1 x 2
×13
Plant, Flower, Minifig Accessory with 7 Thick Petals and Pin, Center Ring
×9
Plant, Stem with 3 Leaves and Bottom Pin
×8
Bar 1L / Stem with 3 Sprouts/Prongs
×7
Plate Round 1 x 1 with Open Stud
×7
Wedge 2 x 2 Facet
×7
Plant, Flower, Plate Round 1 x 1 with 5 Petals
×6
Bar 1L with Clip [Cut Edges and One Side Hole] [Full Clip]
×6
Plant, Leaves Stacked 4 x 5 x 1 2/3
×6
Plant, Leaves Stacked 4 x 5 x 1 2/3
×6
Bar 2L with Stop in Center
×6
Wedge Sloped 45° 2 x 2 Corner
×5
Bar Holder with Hole and Bar Handle
×5
Plate 1 x 1
×5
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×5
Tile Round 1 x 1 with Hollow Bar
×4
Plate 2 x 2
×4
Plate 1 x 2
×4
Tile 2 x 2 with Groove
×4
Plate 1 x 4
×4
Equipment Candlestick
×4
Plate 2 x 6
×4
Plate Round Corner 6 x 6
×4
Plate Special 1 x 1 with Clip Horizontal [Thick Open O Clip]
×4
Plate Round Corner 5 x 5 with 4 x 4 Round Cutout
×4
Plate Round 1 x 1 with Open Stud
×4
Large Figure Weapon Lightsaber Hilt with Axle Hole and Two Bar Holders
×3
Brick 1 x 1
×3
Plate 1 x 2
×3
Plant, Flower, Minifig Accessory with 7 Thick Petals and Pin, Center Ring
×3
Technic Axle Connector Smooth [with x Hole + Orientation]
×3
Plate Round 1 x 1 with Open Stud
×3
Weapon Bladed Claw Spread
×2
Slope Curved 2 x 1 No Studs [1/2 Bow]
×2
Plate Special 1 x 2 with 1 Stud with Groove and Inside Stud Holder (Jumper)
×2
Tile Special 1 x 1 with Clip with Rounded Edges
×2
Plate Round 1 x 2 Half Circle with Stud (Jumper)
×2
Brick 2 x 2 Corner
×2
Wedge Plate 2 x 2 Cut Corner
×2
Plate 1 x 1
×2
Tile 1 x 2 with Groove
×2
Technic Axle 4
×2
Brick Round 2 x 2 with Axle Hole
×2
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×2
Technic Axle 3
×2
Bar 2L with Stop in Center
×2
Plate Round 1 x 1 with Open Stud
×2
Brick Special 2 x 2 with Grooves and Axle Hole
×2
Slope Curved 4 x 1 No Studs [Stud Holder with Symmetric Ridges]
×1
Plate Special 1 x 2 with Clip Horizontal on Side
×1
Slope Curved 2 x 2 x 2/3
×1
Plant, Flower Stem with Bar and 6 Stems
×1
Wedge Plate 2 x 2 Left
×1
Wedge Plate 2 x 2 Right
×1
Food Egg with 1.5mm Hole [Plain]
×1
Plate Special 1 x 1 Rounded with Handle
×1
Brick 1 x 2
×1
Plate 2 x 3
×1
Plate 2 x 2
×1
Bar 4L (Lightsaber Blade / Wand)
×1
Slope 45° 2 x 1 with Bottom Pin
×1
Tile 1 x 2 with Groove
×1
Technic Axle 2 Notched
×1
Slope Curved 2 x 2 x 2/3 Inverted
×1
Bar 1L with Clip [Cut Edges and One Side Hole] [Full Clip]
×1
Cone 2 x 2 x 2, Open Stud
×1
Plate 6 x 6
×1
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×1
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×1
Plate Special 1 x 4 Offset with Bar Holes
×1
Brick Special 1 x 1 Studs on 4 Sides
×1
Plant, Pumpkin
×1
Animal Body Part, Barb / Claw / Tooth / Talon / Horn, Small
×1
Plate Special 1 x 1 with Clip Horizontal [Thick Open O Clip]
×1
Bar 1L / Stem with 3 Sprouts/Prongs
×1
Plate Round 1 x 1 with Open Stud
×1
Plate Special 2 x 2 with Groove and Center Stud (Jumper)
×1
Bracket 1 x 2 - 2 x 2 Inverted
×1
Weapon Bladed Claw Spread
×1
Tile Round 1 x 1 with Hollow Bar
×1
Plant, Flower, Plate Round 1 x 1 with 5 Petals
×1
Plate 1 x 1
×1
Plate 1 x 1
×1
Plant, Stem with 3 Leaves and Bottom Pin
×1
Plant, Flower, Minifig Accessory with 7 Thick Petals and Pin, Center Ring
×1
Plant, Flower, Minifig Accessory with 7 Thick Petals and Pin, Center Ring
×1
Animal Body Part, Barb / Claw / Tooth / Talon / Horn, Small
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Bar 1L / Stem with 3 Sprouts/Prongs
×1
Bar 1L / Stem with 3 Sprouts/Prongs
×1
Bar 2L with Stop in Center
×1
Bar 2L with Stop in Center
×1
Plate Round 1 x 1 with Open Stud
×1
Plate Round 1 x 1 with Open Stud
×1
Plate Round 1 x 1 with Open Stud
×1
Plate Round 1 x 1 with Open Stud
×1
Plate Round 1 x 1 with Open Stud
×1