
The Flying Dutchman
미니피규어 (3)

SpongeBob Squarepants in Pirate Outfit
fig-003289×1

Patrick Star in Pirate Outfit
fig-003290×1

Flying Dutchman
fig-003291×1
부품 목록 (95)

Plate Round 1 x 1 with Solid Stud
×12
Tile 1 x 4 with Groove
×11
Plate 1 x 2
×10
Slope 45° 2 x 1 with Bottom Pin
×10
Brick Special 1 x 2 Palisade [aka Log]
×9
Cone 1 x 1 [Top Groove]
×9
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×7
Brick Round 1 x 1 Open Stud
×6
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×6
Brick Special 1 x 2 with Vertical Clip [Thick U Clip]
×5
Plate 2 x 6
×5
Hinge Brick 1 x 2 Base
×5
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×5
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×4
Window 1 x 2 x 2 2/3 with Rounded Top
×4
Window 1 x 2 x 2 & 2/3 Pane Twisted Bar with Rounded Top
×4
Equipment Flotation Ring [Life Preserver]
×4
Brick Arch 1 x 4
×4
Hinge Brick 1 x 2 Top Plate Thin
×4
Technic Pin 1/2
×4
Cone 1 x 1 [Top Groove]
×4
Plant, Palm Leaf Small
×4
Tile 1 x 4 with Groove
×3
Brick Special 1 x 2 Palisade [aka Log]
×3
Plate 2 x 4
×3
Brick Round 1 x 1 Open Stud
×3
Brick Round 1 x 1 Open Stud
×3
Plate Round 1 x 1 with Solid Stud
×3
Tile Special 1 x 1 with Clip with Rounded Tips
×2
Equipment Goblet / Glass
×2
Slope Inverted 75° 2 x 1 x 3
×2
Weapon Sword / Cutlass
×2
Plate Special 2 x 2 with 2 Pin Holes
×2
Brick Arch 1 x 5 x 4 Inverted
×2
Brick Special 1 x 4 with 4 Studs on One Side
×2
Slope 45° 2 x 2 Double Concave
×2
Plate 1 x 6
×2
Plate 1 x 4
×2
Plate Special 1 x 2 with 1 Stud with Groove (Jumper)
×2
Technic Beam 1 x 2 Thin
×2
Plate Special 1 x 1 with Clip Vertical [Thick Open O Clip]
×2
Plate Special 1 x 2 with Clip Horizontal on End
×2
Plate Special 2 x 2 with Groove and Center Stud (Jumper)
×2
Launcher Base, Weapon Cannon Base 2 x 4
×1
Bar, 4 Top Bars, Palm Tree Top
×1
Brick 2 x 4
×1
Brick 2 x 4
×1
Plate 2 x 3
×1
Plate 2 x 3
×1
Plate 2 x 3
×1
Plate 2 x 2
×1
Plate 2 x 8
×1
Plate 4 x 8
×1
Plate 4 x 8
×1
Bar 4L (Lightsaber Blade / Wand)
×1
Wedge Plate 8 x 8 Cut Corner
×1
Panel 4 x 4 x 6 Quarter Cylinder with Skull and Crossed Swords Print [3817]
×1
Tile 2 x 2 with Nautical Map and Red 'X' Print
×1
Tile 1 x 2 with Groove
×1
Wedge Plate 4 x 6 Cut Corners
×1
Plate 1 x 8
×1
Technic Axle 12
×1
Steering Stand 1 x 2 with Black Steering Wheel
×1
Equipment Shovel [Rounded Handle End]
×1
Plate Special 1 x 2 with Handles [Flat Ends / Low Attachment]
×1
Technic Brick 1 x 6 [5 Pin Holes]
×1
Brick Round 2 x 2 with Axle Hole
×1
Plate Round 2 x 2 with Axle Hole Type 1 (+ Opening)
×1
Flag 2 x 2 Trapezoid with Flat Area between Clips
×1
Flag 4 x 1 Wavy [First Wave Right]
×1
Technic Axle 3
×1
Treasure Chest Bottom with Rear Slots, with Groove
×1
Treasure Chest Lid [Thick Hinge]
×1
Dish 2 x 2 Inverted [Radar]
×1
Plate Special 1 x 2 [Side Handle Closed Ends]
×1
Panel 1 x 2 x 1 [Square Corners]
×1
Bar 1L with Clip [Cut Edges and One Side Hole] [Gap in Clip]
×1
Technic Axle Connector Smooth [with x Hole + Orientation]
×1
Bar 12L with Open Stud, Towball, and Top Slit [Boat Mast]
×1
Brick Curved 1 x 2 x 1 1/3 with Curved Top
×1
Hinge Brick 2 x 2 Top Plate Thin
×1
Bag / Messenger Pouch with Long Strap
×1
Brick Special 2 x 2 with Pin and Axle Hole
×1
Bar 6L with Stop Ring
×1
Barrel Half Large with Axle Hole
×1
Hose Rigid 3mm D. 12L / 9.6cm
×1
Launcher, Weapon Cannon Shooting
×1
Aircraft Fuselage Curved Aft Section 6 x 10 Bottom
×1
Plate Round 1 x 1 with Solid Stud
×2
Weapon Sword / Cutlass
×1
Technic Pin 1/2
×1
Bar 1L with Clip [Cut Edges and One Side Hole] [Gap in Clip]
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×1
Plate Round 1 x 1 with Solid Stud
×1