
Twin-Rotor Helicopter
미니피규어 (1)
부품 목록 (215)

Tile Round 1 x 1
×14
Technic Pin with Friction Ridges Lengthwise and Center Slots
×12
Slope 45° 2 x 2
×10
Plate 1 x 4
×10
Plate 1 x 2
×9
Plate 1 x 2
×9
Technic Axle 2 Notched
×8
Technic Brick 1 x 2 with Axle Hole Type 1 [+ Opening] and Bottom Pin
×8
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×8
Slope 18° 2 x 1 x 2/3 with 4 Slots / Grate
×8
Slope Curved 4 x 1 Double with No Studs
×8
Brick 1 x 1
×7
Plate 2 x 4
×7
Plate 2 x 3
×7
Plate 1 x 2
×7
Slope Curved 2 x 1 No Studs [1/2 Bow]
×6
Tile Special 1 x 2 Grille with Bottom Groove
×6
Plate 2 x 3
×6
Technic Plate 1 x 5 with Smooth Ends, 4 Studs and Centre Axle Hole
×6
Wheel 8 x 6 with Slot
×6
Wedge Plate 3 x 2 Left
×6
Tyre 14 x 4 Smooth Small Single [New Style]
×6
Brick Curved 1 x 2 x 1 1/3 with Curved Top
×6
Plate Special 2 x 16 with Angled Side Extensions and Hole (Rotor Blade)
×6
Tile 1 x 3
×6
Technic Gear 12 Tooth Bevel
×6
Slope 30° 1 x 2 x 2/3
×6
Panel 1 x 2 x 2 [Side Supports / Hollow Studs]
×6
Brick 1 x 6
×5
Technic Brick 1 x 2 [1 Pin Hole]
×5
Slope Curved 4 x 1 No Studs [Stud Holder with Symmetric Ridges]
×4
Slope Curved 2 x 1 No Studs [1/2 Bow]
×4
Panel 1 x 4 x 1 with Rounded Corners [Thin Wall]
×4
Plate 2 x 2 Corner
×4
Plate 2 x 2 Corner
×4
Brick 2 x 3
×4
Brick 1 x 4
×4
Plate 2 x 2
×4
Plate 1 x 1
×4
Plate 2 x 8
×4
Technic Axle and Pin Connector Angled #3 - 157.5°
×4
Technic Plate Rotor 3 Blade with Smooth Ends and 6 Studs (Propeller)
×4
Plate Special 1 x 3 with 2 Studs with Groove and Inside Stud Holder (Jumper)
×4
Slope Inverted 45° 2 x 2 [Ovoid Bottom Pin, Bar-sized Stud Holes]
×4
Slope Inverted 45° 2 x 1
×4
Plate 1 x 6
×4
Technic Brick 1 x 2 [1 Pin Hole]
×4
Technic Pin 1/2
×4
Brick Curved 1 x 2 x 1 1/3 with Curved Top
×4
Plate Round 1 x 1 with Open Stud
×4
Brick Special 1 x 1 with Stud on 1 Side
×4
Plate Special 1 x 2 [Top Clip]
×4
Brick Round 2 x 2, Pin Holes
×3
Tile Special 1 x 2 Grille with Bottom Groove
×3
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×3
Tile 2 x 3
×3
Brick 1 x 2
×3
Plate 1 x 2
×3
Plate 1 x 2
×3
Plate 4 x 4
×3
Plate 2 x 8
×3
Bar 4L (Lightsaber Blade / Wand)
×3
Plate 1 x 6
×3
Plate 1 x 6
×3
Technic Brick 1 x 2 [1 Pin Hole]
×3
Plate 1 x 4
×3
Plate 1 x 4
×3
Plate 2 x 6
×3
Plate 6 x 6
×3
Wedge Plate 4 x 2 Right
×3
Wedge Plate 4 x 2 Left
×3
Wheel Holder 2 x 2 Thin with Split Wheel Clip Pins
×3
Gearbox 4 x 4 x 1 2/3 with 1 x 2 Cutouts, Pin Holes
×3
Bracket 1 x 2 - 1 x 2 Inverted
×3
Slope Curved 4 x 1 No Studs [Stud Holder with Symmetric Ridges]
×2
Plate 3 x 3
×2
Plate Special 1 x 2 with Pin Hole on Top
×2
Slope Curved 2 x 1 No Studs [1/2 Bow]
×2
Slope Curved 4 x 1 Inverted
×2
Slope Curved 4 x 1 Inverted
×2
Tile Round 2 x 2 with Hole
×2
Plate Special 1 x 2 with 1 Stud with Groove and Inside Stud Holder (Jumper)
×2
Tile Special 1 x 1 with Clip with Rounded Edges
×2
Technic Gear 20 Tooth Double Bevel with Axle Hole Type 1 [+ Opening]
×2
Brick Special 1 x 2 x 1 2/3 with 4 Studs on 1 Side
×2
Slope Curved 3 x 2 No Studs
×2
Slope Curved 3 x 2 No Studs
×2
Tile 1 x 4 with Groove
×2
Tile Special 1 x 2 with Handle
×2
Brick Special 1 x 2 with Pin
×2
Brick 1 x 16
×2
Wedge Plate 2 x 2 Cut Corner
×2
Wedge Plate 2 x 2 Cut Corner
×2
Brick 1 x 1
×2
Plate 2 x 4
×2
Plate 2 x 4
×2
Plate 1 x 1
×2
Plate 4 x 6
×2
Brick Special 1 x 4 with 4 Studs on One Side
×2
Brick Special 1 x 4 with 4 Studs on One Side
×2