
Shuttle Transporter
부품 목록 (137)

Slope Curved 2 x 2 x 2/3
×11
Bracket 1 x 2 - 2 x 2
×11
Plate 1 x 2
×10
Brick Round 1 x 1 Open Stud
×10
Tile Special 1 x 2 Grille with Bottom Groove
×9
Plate 1 x 1
×9
Plate Round 1 x 1 with Open Stud
×9
Slope 30° 1 x 2 x 2/3
×8
Plate 2 x 2
×7
Plate 1 x 2
×7
Plate 1 x 2
×6
Plate Special 1 x 2 Rounded with 2 Open Studs
×6
Brick Curved 1 x 2 x 1 1/3 with Curved Top
×6
Tyre 17.5 x 6 with Shallow Staggered Treads and Middle Band
×6
Wheel 11 x 6 with 8 Spokes
×6
Bracket 1 x 2 - 1 x 2 Inverted
×6
Tile Special 1 x 2 Grille with Bottom Groove
×5
Plate 1 x 4
×5
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×5
Tile Round 1 x 1
×5
Slope Curved 2 x 1 No Studs [1/2 Bow]
×4
Plate 2 x 3
×4
Plate 2 x 3
×4
Tile 1 x 2 with Groove
×4
Tile 1 x 1 with Groove
×4
Wheel 8 x 6 with Slot
×4
Wheel 8 x 6 with Slot
×4
Plate Special 1 x 1 with Clip Horizontal [Thick Open O Clip]
×4
Tyre 15 x 6 Offset Tread Small with Band around Center
×4
Tile Round 1 x 1
×4
Plate Special 1 x 2 with Handles on Ends
×3
Brick 2 x 4
×3
Plate 2 x 4
×3
Bar 4L (Lightsaber Blade / Wand)
×3
Plate 1 x 4
×3
Wedge Plate 4 x 2 Right
×3
Wedge Plate 4 x 2 Left
×3
Dish 2 x 2 Inverted [Radar]
×3
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×3
Plate Special 2 x 2 with Wheels Holder Wide
×3
Plate Special 1 x 2 [Top Clip]
×3
Brick Round 2 x 2 Truncated Cone
×3
Brick Special 1 x 2 with 2 Studs on 1 Side
×2
Slope Curved 2 x 2 x 2/3
×2
Plate Special 1 x 2 with 1 Stud with Groove and Inside Stud Holder (Jumper)
×2
Panel 1 x 2 x 1 with Rounded Corners and 2 Sides
×2
Plate 2 x 2 Corner
×2
Plate 2 x 2 Corner
×2
Slope Curved 2 x 1 Inverted
×2
Plate Round 2 x 2 with Rounded Bottom [Boat Stud]
×2
Bracket 1 x 2 - 1 x 4 [Rounded Corners at Bottom, Square Corners at Top]
×2
Brick 1 x 2
×2
Brick 1 x 2
×2
Brick 1 x 1
×2
Plate 2 x 4
×2
Plate 2 x 4
×2
Plate 2 x 4
×2
Plate 1 x 2
×2
Plate 1 x 1
×2
Wedge Plate 4 x 4 Cut Corner
×2
Brick 1 x 2 without Bottom Tube
×2
Tile 1 x 2 with Groove
×2
Tile 1 x 1 with Groove
×2
Plate Special 1 x 2 with Door Rail
×2
Plate Round 1 x 1 with Hollow Stud and Horizontal Bar 1L
×2
Brick 1 x 3
×2
Brick Curved 1 x 2 x 1 No Studs
×2
Brick Round 2 x 2 with Axle Hole
×2
Tile 1 x 8 with Groove
×2
Tile 1 x 8 with Groove
×2
Plate 1 x 10
×2
Plate Special 1 x 8 with Door Rail
×2
Tap 1 x 1 without Hole in Spout
×2
Plate Special 2 x 2 with Wheel Holders
×2
Wheel Holder 2 x 2 Thin with Split Wheel Clip Pins
×2
Slope 30° 1 x 1 x 2/3 (Cheese Slope)
×2
Plate Special 1 x 1 with Clip Vertical [Thick Open O Clip]
×2
Wedge Plate 6 x 6 Cut Corner
×2
Tile 1 x 3
×2
Bracket 1 x 2 - 1 x 2 Inverted
×2
Bracket 1 x 2 - 1 x 4 [Rounded Corners]
×1
Bracket 1 x 2 - 1 x 4 [Rounded Corners]
×1
Tile Special 1 x 1 with Clip with Rounded Edges
×1
Plate Special Round 2 x 2 with Center Stud (Jumper Plate)
×1
Bar Holder with Hole and Bar Handle
×1
Wheel Holder 2 x 2 Thin with Clips, Plane Single
×1
Tile 1 x 4 with Groove
×1
Plate 2 x 12
×1
Propeller 4 Blade 5 Diameter with Rounded Ends, Open Hub
×1
Plate Special 1 x 2 Side Handle [Free Ends]
×1
Tile 2 x 3
×1
Brick Curved 2 x 2, Two Top Studs
×1
Plate 2 x 4
×1
Plate 2 x 3
×1
Plate 2 x 2
×1
Plate 4 x 10
×1
Plate 4 x 4
×1
Plate 2 x 8
×1
Tile Special 2 x 3 with 2 Clips [Thick Open O Clips]
×1
Plate 6 x 8
×1